Water and gas/water assisted injection molding of polymers

被引：0
|
作者：
BociĄga, Elzbieta [1 ]
机构：
[1] Politechnika Czȩstochowska, Instytut Przetwoárstwa Polimeroáw i ZarzĄdzania ProdukcjĄ, Al. Armii Krajowej 19c, 42-200 Czȩstochowa, Poland
来源：
Polimery/Polymers | 2007年 / 52卷 / 02期
关键词：
D O I：
10.14314/polimery.2007.088
中图分类号：
学科分类号：
摘要：
引用
收藏
页码：88 / 93
相关论文
共 50 条
  • [31] An Experimental Setup to Measure the Transient Temperature Profiles in Water Assisted Injection Molding
    Liu, S-J
    Su, P-C
    INTERNATIONAL POLYMER PROCESSING, 2009, 24 (03) : 234 - 241
  • [32] Water-assisted injection molding of thermoplastic materials: Effects of processing parameters
    Liu, SJ
    Chen, YS
    POLYMER ENGINEERING AND SCIENCE, 2003, 43 (11): : 1806 - 1817
  • [33] Simulation and analysis on cavity filling process in water-assisted injection molding
    Zhang Z.
    Zhou H.
    Gao Y.
    Yang H.
    Jixie Gongcheng Xuebao/Journal of Mechanical Engineering, 2010, 46 (08): : 140 - 146
  • [34] Dynamic visualization of cavity-filling process in fluid-assisted injection molding-gas versus water
    Liu, Shih-Jung
    Wu, Yi-Chuan
    POLYMER TESTING, 2007, 26 (02) : 232 - 242
  • [35] Influence of cross section of cavity on water penetration during overflow water-assisted injection molding process
    Kuang, Tangqing
    Yu, Chuncong
    Deng, Yang
    Zhang, Kai
    Huagong Xuebao/CIESC Journal, 2014, 65 (10): : 4176 - 4182
  • [36] Gas assisted injection molding of a vacuum cleaner body
    Rhee, BO
    Ahn, HK
    Lee, KD
    Yu, BK
    Son, CW
    ANTEC '99: PLASTICS BRIDGING THE MILLENNIA, CONFERENCE PROCEEDINGS, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPECIAL AREAS;, 1999, : 571 - 575
  • [37] Application of Moldflow in Gas-assisted Injection Molding
    Zi, Ke Ming
    Chen, Li Heng
    MECHATRONICS AND MATERIALS PROCESSING I, PTS 1-3, 2011, 328-330 : 1202 - +
  • [38] Residual stresses in gas-assisted injection molding
    Custodio, Frederico J. M. F.
    Anderson, Patrick D.
    Peters, Gerrit W. M.
    Cunha, Antonio M.
    Meijer, Han E. H.
    RHEOLOGICA ACTA, 2010, 49 (01) : 23 - 44
  • [39] On the dynamics of gas-assisted injection molding process
    Chang, RY
    Tsai, MH
    Hsu, CH
    ANTEC'97 - PLASTICS SAVING PLANET EARTH, CONFERENCE PROCEEDINGS, VOLS 1 - 3, 1997, : 598 - 602
  • [40] Flow directions in the gas assisted injection molding technology
    Soh, YS
    Chung, CH
    ANTEC'97 - PLASTICS SAVING PLANET EARTH, CONFERENCE PROCEEDINGS, VOLS 1 - 3, 1997, : 603 - 609
12345