Calculation Method of Time-varying Meshing Stiffness of Small Module Gear Transmissions

被引：1
|
作者：
Hu B. [1 ]
An J. [1 ]
Yin L. [1 ]
Zhou C. [2 ]
机构：
[1] College of Automotive and Mechanical Engineering, Changsha University of Science and Technology, Changsha
[2] College of Mechanical and Vehicle Engineering, Hunan University, Changsha
来源：
Zhongguo Jixie Gongcheng/China Mechanical Engineering | 2024年 / 35卷 / 01期
关键词：
center distance error; shaft hole fit clearance; small module gear; time-varying meshing stiffness;
D O I：
10.3969/j.issn.1004-132X.2024.01.007
中图分类号：
学科分类号：
摘要：
Due to the small center distance, the dynamic performance of small modulus gear transmissions was very sensitive to the center distance errors. In addition, the intermediate gears were often designed to rotate at high speed on the fixed shaft, and there were clearances between the gear center hole and the shaft. Therefore, the calculation model of the gear mesh characteristic parameters. and time-varying mesh stiffness under the influences of the center distance errors and the shaft hole fit clearances was established, and the influence laws of the two factors mentioned on the mesh stiffness were investigated. The results show that the center distance errors will change the contact degree and meshing stiffness of the gear pairs. The shaft hole clearance causes the actual center distance to fluctu- ate periodically around the theoretical center distance, which leads to the coexistence of the strengthe- ning and weakening regions of the meshing stiffness in the whole cycle. The influences of center dis- tance errors and shaft hole fit clearances both superimposed and weakened each other in different angle ranges, resulting in the difference in meshing stiffness of each gear tooth, and the risk of inducing greater vibration and different noise. © 2024 Chinese Mechanical Engineering Society. All rights reserved.
引用
收藏
页码：74 / 82
页数：8
相关论文
共 30 条
  • [11] CHEN Z., SHAO Y., Mesh Stiffness Calculation of a Spur Gear Pair with Tooth Profile Modification and Tooth Root Crack [J], Mechanism and Ma- chine Theory, 62, pp. 63-74, (2013)
  • [12] SHAO Y, CHEN Z., Dynamic Features of Planeta- ry Gear Set with Tooth Plastic Inclination Deform ation due to Tooth Root Crack[J], Nonlinear Dy- namics, 74, 4, pp. 1253-1266, (2013)
  • [13] MA H., LI Z., FENG M, Et al., Time-varying Mesh Stiffness Calculation of Spur Gears with Spalling Defect[J], Engineering Failure Analysis, 66, pp. 166-176, (2016)
  • [14] YU W., SHAO Y., MECHEFSKE CK., The Effects of Spur Gear Tooth Spatial Crack Propaga- tion on Gear Mesh Stiffness [J], Engineering Fail-ure Analysis, 54, pp. 103-119, (2015)
  • [15] MENG Zong, LI Jiasong, PAN Zuozhou, Et al., Analysis of Influence of Crack Failure on Time-va- rying Meshing Stiffness of Gear Teeth, China Mechanical Engineering, 33, 16, pp. 1897-1905, (2022)
  • [16] MA H., FENG MJ, LI Z W, Et al., Time-varying Mesh Characteristics of a Spur Gear Pair Considering the Tip-fillet and Friction [J], Meccanica, 52, 7, pp. 1695-1709, (2017)
  • [17] HU B, ZHOU C., WANG H., Et al., Nonlinear Tribo-dynamic Model and Experimental Verifica- tion of a Spur Gear Drive under Loss of lubrication Condition[J], Mechanical Systems and Signal Processing, 153, (2021)
  • [18] CHEN K., HUANGFU Y, MA H., Et al., Calcula-tion of Mesh Stiffness of Spur Gears Considering Complex Foundation Types and Crack Propagation. Paths[J], Mechanical Systems and Signal Process ing, 130, pp. 273-292, (2019)
  • [19] WANG J., HOWARD I., The Torsional Stiffness of Involute Spur Gears[J], ARCHIVE Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science, 218, 1, pp. 131-142, (2004)
  • [20] TANG Jinyuan, PU Taiping, Mesh stiffness Cal- culation of Spiral Bevel Gear Based on Finite Ele ment Method, Journal of Mechanical Engineer- ing, 47, 11, pp. 23-29, (2011)
123