Effects of cooling rate on the microstructure and properties of magnesium alloy-a review

被引：0
|
作者：
Cai, Huisheng [1 ]
Zhang, Nannan [2 ]
Liu, Liang [1 ]
Su, Juan [1 ]
Li, Yuguang [1 ]
Kang, Yu [1 ]
Guo, Feng [1 ]
机构：
[1] Inner Mongolia Univ Technol, Sch Mat Sci & Engn, Inner Mongolia Key Lab Thin Film & Coatings, Hohhot 010051, Peoples R China
[2] Shanghai Tech Inst Elect & Informat, Sch Sino German Engn, Shanghai 201411, Peoples R China
来源：
JOURNAL OF MAGNESIUM AND ALLOYS | 2024年 / 12卷 / 08期
基金：
中国国家自然科学基金;
关键词：
Magnesium alloy; Cooling rate; Microstructure; Mechanical properties; Corrosion resistance; Oxidation resistance; DENDRITE COHERENCY POINT; MECHANICAL-PROPERTIES; SOLIDIFICATION CHARACTERISTICS; RAPID SOLIDIFICATION; CORROSION-RESISTANCE; GRAIN-REFINEMENT; THERMAL-ANALYSIS; SOLUTE REDISTRIBUTION; RESIDUAL-STRESS; FLOW-STRESS;
D O I：
10.1016/j.jma.2024.06.021
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
Magnesium alloy is one of the most widely used lightweight structural materials, and the development of high strength-toughness magnesium alloy is an important research field at present and even in the future. The preparation process parameters of magnesium alloy directly affect the microstructure of the magnesium alloy, and then determine the properties of the magnesium alloy. The cooling rate has important effects on the microstructure and properties of the magnesium alloy, and is an important preparation process parameter that cannot be ignored. Both the cooling rate from liquid phase to solid phase and the cooling rate of the magnesium alloy after heat treatment will change the microstructure of the magnesium alloy. Furthermore, the properties of magnesium alloy will be affected. In this paper, the effects of cooling rate on the solidification behavior, the rheological behavior, the change of microstructure (the solid solution of alloying elements in matrix, the composition, size, distribution and morphology of second phase, the diffusion and segregation of alloying elements, the grain size, the formation and morphology of dendrite, etc.), and the effects of cooling rate of magnesium alloy after heat treatment on the microstructure and stress distribution are reviewed. The reasons for the divergence about the influence of cooling rate on the microstructure of magnesium alloy are analyzed in detail. The effects of cooling rate on the mechanical properties, corrosion resistance and oxidation resistance of magnesium alloy are also analyzed and discussed deeply. Finally, the new methods and approaches to study the effects of cooling rate on the microstructure and properties of magnesium alloy are prospected. (c) 2024 Chongqing University. Publishing services provided by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY-NC-ND license ( http://creativecommons.org/licenses/by-nc-nd/4.0/ ) Peer review under responsibility of Chongqing University
引用
收藏
页码：3094 / 3114
页数：21
相关论文
共 50 条
  • [41] Effects of minor addition and cooling rate on the microstructure of cast magnesium-silicon alloys
    Quimby, P. D.
    Lu, S. Z.
    Plichta, M. R.
    Visser, D. K.
    Jacobe, K. P.
    MAGNESIUM TECHNOLOGY 2006, PROCEEDINGS, 2006, : 535 - +
  • [42] EFFECT OF MOULD COMPONENTS ON THE COOLING RATE, MICROSTRUCTURE, AND QUALITY OF WE43 MAGNESIUM CASTING ALLOY
    Dybowski, B.
    Kielbus, A.
    Jarosz, R.
    ARCHIVES OF METALLURGY AND MATERIALS, 2014, 59 (04) : 1527 - 1532
  • [43] Microhardness and microstructure characteristics of AZ91 magnesium alloy under different cooling rate conditions
    Abd El-Rehim, A. F.
    Zahran, H. Y.
    Al-Masoud, H. M.
    Habashy, D. M.
    MATERIALS RESEARCH EXPRESS, 2019, 6 (08)
  • [44] Effect of cooling rate on the microstructure and microhardness of the CuZrAgAl alloy
    Liu, Y.
    Blandin, J. J.
    Suery, M.
    Kapelski, G.
    MATERIALS CHARACTERIZATION, 2012, 70 : 8 - 13
  • [45] Effect of cooling rate on microstructure and tensile properties of Zr-3.1 Nb alloy
    Wang, Qi
    Xing, Xiangdong
    Wang, Sunxuan
    Lyu, Ming
    CAILIAO GONGCHENG-JOURNAL OF MATERIALS ENGINEERING, 2023, 51 (05): : 112 - 119
  • [46] Effect of aging cooling rate on microstructure and properties of alloy CuNi2Si
    Pan, Jiangue
    Liu, Hefa
    Xie, Chunsheng
    Dai, Anlun
    Lu, Xiufen
    Yu, Lihua
    Jinshu Rechuli/Heat Treatment of Metals, 1993, (03): : 24 - 27
  • [47] Effect of cooling rate on microstructure and mechanical properties of TC16 titanium alloy
    Zhang Z.-Q.
    Dong L.-M.
    Hu M.
    Lei X.-F.
    Yang Y.
    Yang R.
    Zhongguo Youse Jinshu Xuebao/Chinese Journal of Nonferrous Metals, 2019, 29 (07): : 1391 - 1398
  • [48] Cooling Rate and Size Effect on the Microstructure and Mechanical Properties of AlCoCrFeNi High Entropy Alloy
    Wang, F. J.
    Zhang, Y.
    Chen, G. L.
    Davies, H. A.
    JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME, 2009, 131 (03):
  • [49] EFFECT OF COOLING RATE ON MICROSTRUCTURE AND TENSILE PROPERTIES IN Ti3Al ALLOY
    Wang Zhen
    Cao Lei
    Liu Renci
    Liu Dong
    Cui Yuyou
    Yang Rui
    ACTA METALLURGICA SINICA, 2013, 49 (11) : 1487 - 1492
  • [50] Effect of cooling rate on microstructure, mechanical properties and residual stress of 7075 aluminum alloy
    Koc, Funda Gul
    Col, Mustafa
    Celiker, Tanju
    MATERIALS TESTING, 2018, 60 (10) : 989 - 996
12345