Effects of cooling rate on the microstructure and properties of magnesium alloy-a review

被引:0
|
作者
Cai, Huisheng [1 ]
Zhang, Nannan [2 ]
Liu, Liang [1 ]
Su, Juan [1 ]
Li, Yuguang [1 ]
Kang, Yu [1 ]
Guo, Feng [1 ]
机构
[1] Inner Mongolia Univ Technol, Sch Mat Sci & Engn, Inner Mongolia Key Lab Thin Film & Coatings, Hohhot 010051, Peoples R China
[2] Shanghai Tech Inst Elect & Informat, Sch Sino German Engn, Shanghai 201411, Peoples R China
基金
中国国家自然科学基金;
关键词
Magnesium alloy; Cooling rate; Microstructure; Mechanical properties; Corrosion resistance; Oxidation resistance; DENDRITE COHERENCY POINT; MECHANICAL-PROPERTIES; SOLIDIFICATION CHARACTERISTICS; RAPID SOLIDIFICATION; CORROSION-RESISTANCE; GRAIN-REFINEMENT; THERMAL-ANALYSIS; SOLUTE REDISTRIBUTION; RESIDUAL-STRESS; FLOW-STRESS;
D O I
10.1016/j.jma.2024.06.021
中图分类号
TF [冶金工业];
学科分类号
0806 ;
摘要
Magnesium alloy is one of the most widely used lightweight structural materials, and the development of high strength-toughness magnesium alloy is an important research field at present and even in the future. The preparation process parameters of magnesium alloy directly affect the microstructure of the magnesium alloy, and then determine the properties of the magnesium alloy. The cooling rate has important effects on the microstructure and properties of the magnesium alloy, and is an important preparation process parameter that cannot be ignored. Both the cooling rate from liquid phase to solid phase and the cooling rate of the magnesium alloy after heat treatment will change the microstructure of the magnesium alloy. Furthermore, the properties of magnesium alloy will be affected. In this paper, the effects of cooling rate on the solidification behavior, the rheological behavior, the change of microstructure (the solid solution of alloying elements in matrix, the composition, size, distribution and morphology of second phase, the diffusion and segregation of alloying elements, the grain size, the formation and morphology of dendrite, etc.), and the effects of cooling rate of magnesium alloy after heat treatment on the microstructure and stress distribution are reviewed. The reasons for the divergence about the influence of cooling rate on the microstructure of magnesium alloy are analyzed in detail. The effects of cooling rate on the mechanical properties, corrosion resistance and oxidation resistance of magnesium alloy are also analyzed and discussed deeply. Finally, the new methods and approaches to study the effects of cooling rate on the microstructure and properties of magnesium alloy are prospected. (c) 2024 Chongqing University. Publishing services provided by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY-NC-ND license ( http://creativecommons.org/licenses/by-nc-nd/4.0/ ) Peer review under responsibility of Chongqing University
引用
收藏
页码:3094 / 3114
页数:21
相关论文
共 50 条
  • [1] Effects of cooling rate on the microstructure and properties of magnesium alloy-a review
    Huisheng Cai
    Nannan Zhang
    Liang Liu
    Juan Su
    Yuguang Li
    Yu Kang
    Feng Guo
    Journal of Magnesium and Alloys, 2024, 12 (08) : 3094 - 3114
  • [2] Combined effects of cerium and cooling rate on microstructure and mechanical properties of AZ91 magnesium alloy
    Cai, Huisheng
    Guo, Feng
    Su, Juan
    MATERIALS RESEARCH EXPRESS, 2018, 5 (01):
  • [3] Effects of cooling rate on solidification microstructure of ZK60 magnesium alloy
    Yang, CM
    Zhang, DF
    Ding, PD
    Peng, J
    Chen, XH
    MAGNESIUM - SCIENCE, TECHNOLOGY AND APPLICATIONS, 2005, 488-489 : 295 - 298
  • [4] Effects of Stirring Time and Cooling Rate on the Rheocast Microstructure and Mechanical Properties of Magnesium Alloy MRI 230D
    Zimpel, Igor
    Telles Bartex, Sergio Luiz
    de Barcellos, Vinicius Karlinski
    MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS, 2021, 24 (03):
  • [5] Effect of Cooling Rate on the Microstructure of AZ31 Magnesium Alloy
    Masoumi, M.
    Pekguleryuz, M.
    TRANSACTIONS OF THE AMERICAN FOUNDRY SOCIETY, VOL 117, 2009, 117 : 617 - 626
  • [6] INFLUENCE OF COOLING MEDIUM ON MICROSTRUCTURE AND MECHANICAL PROPERTIES IN FRICTION STIR PROCESSING OF MAGNESIUM ALLOY - A REVIEW
    Rathinasuriyan, C.
    Sankar, R.
    Puviyarasan, M.
    Senthil Kumar, V. S.
    Palanikumar, K.
    SURFACE REVIEW AND LETTERS, 2025, 32 (01)
  • [7] The effect of cooling rate and degassing on microstructure and mechanical properties of cast AZ80 magnesium alloy
    Azqadan, Erfan
    Uramowski, Jared
    Roostaei, Ali A.
    Behravesh, Seyed Behzad
    Javaid, Amjad
    Williams, Bruce W.
    Wells, Mary A.
    Jahed, Hamid
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 844
  • [8] Effects of melt cooling rate on the microstructure and mechanical properties of Al-Cu alloy
    Wang, Lin
    Sun, Yu
    Bo, Lin
    Zuo, Min
    Zhao, Degang
    MATERIALS RESEARCH EXPRESS, 2019, 6 (11)
  • [9] Effects of homogenizing annealing on isothermal cooling on microstructure and properties of AZ91D magnesium alloy
    Yang, Jun-Gang
    Han, Xi
    Bai, Yun
    Cailiao Rechuli Xuebao/Transactions of Materials and Heat Treatment, 2014, 35 (SUPPL.1): : 140 - 145
  • [10] Effects of cooling rate on microstructure, mechanical and corrosion properties of Mg-Zn-Ca alloy
    Wang, Jing-feng
    Huang, Song
    Guo, Sheng-feng
    Wei, Yi-yun
    Pan, Fu-sheng
    TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2013, 23 (07) : 1930 - 1935