AC Ground Fault Location Method for Variable Speed Drives Using Lissajous Curves

被引：0

作者：

Guerrero, Jose Manuel ^{[1
]}

Serrano-Jimenez, Daniel ^{[2
]}

Madina, Patxi ^{[3
]}

Valino, Vanesa ^{[2
]}

Navarro, Gustavo ^{[4
]}

Platero, Carlos A. ^{[5
]}

机构：

[1] Univ Pais Vasco Euskal Herriko Unibertsitatea, Elect Engn Dept, Bilbao 48013, Spain

[2] Univ Politecn Madrid, Energy & Fuels Dept, Madrid 28003, Spain

[3] Mondragon Unibertsitatea, Elect & Comp Dept, Mondragon Arrasate 20500, Spain

[4] Ctr Invest Energet Medioambientales & Tecnol CIEMA, Elect & Elect Dept, Madrid 28040, Spain

[5] Univ Politecn Madrid, Automat Elect & Elect Engn & Ind Comp Dept, Madrid 28007, Spain

来源：

IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS | 2024年 / 60卷 / 06期

关键词：

Voltage measurement; Grounding; Circuit faults; Resistors; Resistance; Fault location; Current measurement; Electrical fault detection; electrical safety; fault diagnosis; fault location; variable speed drives; voltage measurement; SYSTEMS;

D O I：

10.1109/TIA.2024.3446955

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The increasing presence of electric drives demands the development of new detection and diagnosis methods of electrical faults. In particular, ground faults are the most common type of faults in electrical systems. Locating these faults is not trivial, as they depend not only on the position, but also on its fault resistance. This paper proposes a new method to detect and locate ground faults in the AC side of an electric drive. The method is based on the ground connection of a high value resistance between the midpoint of the DC bus and ground. By means of the study of the relations between the DC voltage on this resistance and the phase-to-neutral voltages in the AC side of the drive, the location of the fault can be determined. This method has several advantages, as it does not require to know the phase impedance or to estimate an initial ground resistance. The method has been validated by means of computer simulations and in an experimental test bench using a 140-kW power converter obtaining satisfactory results.

引用

页码：8912 / 8922

页数：11

共 50 条

[31] GROUND FAULT LOCATION INFLUENCE ON AC POWER LINES IMPEDANCES
Vintan, Maria
PROCEEDINGS OF THE ROMANIAN ACADEMY SERIES A-MATHEMATICS PHYSICS TECHNICAL SCIENCES INFORMATION SCIENCE, 2014, 15 (03): : 254 - 261
[32] Fault-tolerant control in variable speed drives: a survey
Campos-Delgado, D. U.
Espinoza-Trejo, D. R.
Palacios, E.
IET ELECTRIC POWER APPLICATIONS, 2008, 2 (02) : 121 - 134
[33] Small variable-speed ac drives: Buy 'em on the Internet
Cleaveland, P
I&CS-INSTRUMENTATION & CONTROL SYSTEMS, 1999, 72 (01): : 80 - 80
[34] Active du/dt filter dimensioning in variable speed AC drives
Strom, J. -P.
Tyster, J.
Korhonen, J.
Purhonen, M.
Silventoinen, P.
PROCEEDINGS OF THE 2011-14TH EUROPEAN CONFERENCE ON POWER ELECTRONICS AND APPLICATIONS (EPE 2011), 2011,
[35] Voltage source inverter fault diagnosis in variable speed AC drives, by the average current Park's Vector approach
Mendes, AMS
Cardoso, AJM
IEMDC'99 - IEEE INTERNATIONAL ELECTRIC MACHINES AND DRIVES CONFERENCE, PROCEEDINGS, 1999, : 704 - 706
[36] Using variable speed drives for evaporative condensers
Reindl, DT
Jekel, TB
ASHRAE JOURNAL, 2005, 47 (08) : 18 - +
[37] Protection and location method of rotor winding grounding fault for variable speed pumping storage unit
Qiao J.
Yin X.
Wang Y.
Lu Q.
Tan L.
Zhu L.
Dianli Zidonghua Shebei/Electric Power Automation Equipment, 2023, 43 (03): : 217 - 224
[38] Energy efficiency in a ground source heat pump with variable speed drives
Del Col, Davide
Azzolin, Marco
Benassi, Giacomo
Mantovan, Mauro
ENERGY AND BUILDINGS, 2015, 91 : 105 - 114
[39] Variable speed ac drives handle loads to 10 hp, are ready for Ethernet
Anon
Control Solutions, 2002, 75 (04):
[40] Identifying Ground Fault Location in High Resistance Grounded Systems using Adjustable Speed Drive
Wei, Lixiang
Liu, Zhijun
Kerkman, Russell J.
Skibinski, Gary L.
2011 IEEE ENERGY CONVERSION CONGRESS AND EXPOSITION (ECCE), 2011, : 2175 - 2182

← 1 2 3 4 5 →