Contact Characteristic Prediction of Double-Locking Toolholder-Spindle System at High Speed

被引：0
|
作者：
Zhao Y. [1 ]
Xu J. [1 ]
Cai L. [1 ]
Liu Z. [1 ]
机构：
[1] College of Mechanical Engineering and Applied Electronics Technology, Beijing University of Technology, Beijing
来源：
| 2017年 / Nanjing University of Aeronautics an Astronautics卷 / 37期
关键词：
Contact stiffness; Double-locking toolholder-spindle; High-speed; Three-dimensional fractal theory;
D O I：
10.16450/j.cnki.issn.1004-6801.2017.04.006
中图分类号：
学科分类号：
摘要：
The finite element analysis is applied to obtain the contact pressure of the contact surfaces at different speed. Based on the three-dimensional fractal model and Hertz theory the contact stiffness of the double locking toolholder-spindle system is obtained, then the simulation model is built to obtain the contact characteristic of the system at high speed. Based on the theoretical model the influences of the different parameters on the taper-surface contact ratio and the contact stiffness are revealed. Finally, the upper limit of the speed and the reasonable ranges of the draw-bar force, disk-spring stiffness and pre-tightening force are defined. All the research results will be a good theoretical basis for the structural design and optimization of the double-locking toolholder-spindle system. © 2017, Editorial Department of JVMD. All right reserved.
引用
收藏
页码：673 / 680
页数：7
相关论文
共 16 条
  • [1] Tsutsumi M., Anno Y., Ebata N., Static characteristics of 7/24 tapered joint for machining center, Bulletin of the JSME, 26, 213, pp. 461-467, (1983)
  • [2] Tsutsumi M., Kuwada Y., Shimizu S., Et al., Static and dynamic stiffness of 1-10 tapered joints for automatic changing, International Journal of Japan Society of Precision Engineering, 30, 4, pp. 301-306, (1995)
  • [3] Aoyama T., Inasaki I., Performances of HSK tool interfaces under high rotational speed, CIRP Annals Manufacturing Technology, 50, 1, pp. 281-284, (2001)
  • [4] Schmitz T.L., Donalson R.R., Predicting high-speed machining dynamics by substructure analysis, CIRP Annals Manufacturing Technology, 49, 1, pp. 303-308, (2000)
  • [5] Schmitz T.L., Davies M.A., Kennedy M.D., Tool point frequency response prediction for high-speed machining by RCSA, Journal of Manufacturing Science and Engineering, 123, 4, pp. 700-707, (2001)
  • [6] Zhao Y., Song X., Cai L., Et al., Surface fractal topography-based contact stiffness determination of spindle-toolholder joint, Journal of Mechanical Engineering Science, 230, 4, pp. 602-610, (2016)
  • [7] Majumdar A., Bhushan B., Fractal model of elastic-plastic contact between rough surfaces, Journal of Tribology, 113, 1, pp. 1-11, (1991)
  • [8] Majumdar A., Tien C.L., Fractal characterization and simulation of rough surfaces, Wear, 136, 2, pp. 313-327, (1990)
  • [9] Li X., Guo H., Liu J., Et al., Fractal model and simulation of normal contact stiffness considering the friction between joint surfaces, Journal of Vibration, Measurement & Diagnosis, 2, pp. 210-213, (2013)
  • [10] Niu Z., Zhang X., Wen S., Et al., Three-dimensional fractal model of tangential contact stiffness of joint interfaces, Journal of Taiyuan University of Science and Technology, 34, 5, pp. 361-367, (2013)
12