Comparison of Fracture Strength of Milled and 3D-Printed Crown Materials According to Occlusal Thickness

被引:2
|
作者
Park, Yeseul [1 ]
Kim, Jimin [1 ]
Kang, You-Jung [2 ]
Shim, Eun-Young [1 ]
Kim, Jee-Hwan [2 ]
机构
[1] Yonsei Univ, Coll Dent, Oral Sci Res Ctr, Dept Prosthodont, Seoul 03722, South Korea
[2] Yonsei Univ, Coll Dent, Dept Prosthodont, Seoul 03722, South Korea
关键词
CAD/CAM; 3D-printed resin; milled hybrid ceramic; permanent prosthesis; fracture strength; Vickers hardness; MECHANICAL-PROPERTIES; 3D; RESISTANCE; RESINS; LOAD;
D O I
10.3390/ma17184645
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
This study aimed to measure the fracture strengths and hardness of final restorative milled and 3D-printed materials and evaluate the appropriate crown thickness for their clinical use for permanent prosthesis. One type of milled material (group M) and two types of 3D-printed materials (groups P1 and P2) were used. Their crown thickness was set to 0.5, 1.0, and 1.5 mm for each group, and the fracture strength was measured. Vickers hardness was measured and analyzed to confirm the hardness of each material. Scanning electron microscopy was taken to observe the surface changes of the 3D-printed materials under loads of 900 and 1500 N. With increased thickness, the fracture strength significantly increased for group M but significantly decreased for group P1. For group P2, the fracture strengths for the thicknesses of 0.5 mm and 1.5 mm significantly differed, but that for 1.0 mm did not differ from those for other thicknesses. The hardness of group M was significantly higher than that of groups P1 and P2. For all thicknesses, the fracture strength was higher than the average occlusal force for all materials; however, an appropriate crown thickness is required depending on the material and component.
引用
收藏
页数:12
相关论文
共 50 条
  • [21] 3D-Printed Mechanochromic Materials
    Peterson, Gregory I.
    Larsen, Michael B.
    Ganter, Mark A.
    Storti, Duane W.
    Boydston, Andrew J.
    ACS APPLIED MATERIALS & INTERFACES, 2015, 7 (01) : 577 - 583
  • [22] 3D-Printed Materials Dentistry
    Becker, Kathrin
    APPLIED SCIENCES-BASEL, 2023, 13 (01):
  • [23] Mechanical properties of 3D-printed and milled composite resins for definitive restorations: An in vitro comparison of initial strength and fatigue behavior
    Prause, Elisabeth
    Malgaj, Tine
    Kocjan, Andraz
    Beuer, Florian
    Hey, Jeremias
    Jevnikar, Peter
    Schmidt, Franziska
    JOURNAL OF ESTHETIC AND RESTORATIVE DENTISTRY, 2024, 36 (02) : 391 - 401
  • [24] Fracture Resistance of 3D-Printed Occlusal Veneers Made from 3Y-TZP Zirconia
    Zenthoefer, Andreas
    Fien, Dennis
    Rossipal, Johannes
    Ilani, Ali
    Schmitt, Clemens
    Hetzler, Sebastian
    Rammelsberg, Peter
    Rues, Stefan
    MATERIALS, 2024, 17 (09)
  • [25] Fracture and transport analysis of heterogeneous 3D-Printed lamellar cementitious materials
    Gupta, Shashank
    Esmaeeli, Hadi S.
    Prihar, Arjun
    Ghantous, Rita M.
    Weiss, W. Jason
    Moini, Reza
    CEMENT & CONCRETE COMPOSITES, 2023, 140
  • [26] Comparative Strength Study of Indirect Permanent Restorations: 3D-Printed, Milled, and Conventional Dental Composites
    Tribst, Joao Paulo Mendes
    Veerman, Adelheid
    Pereira, Gabriel Kalil Rocha
    Kleverlaan, Cornelis Johannes
    Dal Piva, Amanda Maria de Oliveira
    CLINICS AND PRACTICE, 2024, 14 (05) : 1940 - 1952
  • [27] IMPACT STRENGTH OF 3D-PRINTED POLYCARBONATE
    de Vries, Hans
    Engelen, Roy
    Janssen, Esther
    FACTA UNIVERSITATIS-SERIES ELECTRONICS AND ENERGETICS, 2020, 33 (01) : 105 - 117
  • [28] The Effect of Different Surface Treatments on the Roughness, Translucency, and Staining of 3D-Printed Occlusal Device Materials
    Rueda, Silvia Rojas
    Sepsick, Hanna
    Hammamy, Mohammed
    Nejat, Amir H.
    Kee, Edwin
    Lawson, Nathaniel C.
    JOURNAL OF ESTHETIC AND RESTORATIVE DENTISTRY, 2025,
  • [29] Effect of artificial aging on fracture toughness and hardness of 3D-printed and milled 3Y-TZP zirconia
    Alhotan, Abdulaziz
    Yilmaz, Burak
    Weber, Anna
    Babaier, Rua
    Bourauel, Christoph
    Fouda, Ahmed Mahmoud
    JOURNAL OF PROSTHODONTICS-IMPLANT ESTHETIC AND RECONSTRUCTIVE DENTISTRY, 2024,
  • [30] Adaptation of 3D-Printed and Milled Titanium Custom Post and Core
    Alzaid, Abdulaziz A.
    Bukhari, Sarah
    Kattadiyil, Mathew T.
    Alqarni, Hatem
    Alhelal, Abdulaziz A.
    Alanazi, Khalid K.
    Suprono, Montry S.
    Jekki, Rami
    Sahl, Erik F.
    PROSTHESIS, 2024, 6 (06): : 1448 - 1458