Influence of roll speed difference on microstructure, texture and mechanical properties of 7075 aluminum plates produced via combined continuous casting and rolling process

被引:0
|
作者
AMIRI, Mohammad Mehdi [1 ]
FERESHTEH-SANIEE, Faramarz [1 ]
机构
[1] Department of Mechanical Engineering, Faculty of Engineering, Bu-Ali Sina University, Hamedan,65178, Iran
来源
Transactions of Nonferrous Metals Society of China (English Edition) | 2021年 / 31卷 / 04期
关键词
Aluminum alloys - Rolling - Continuous casting - Tensile strength - Hardness - Speed;
D O I
暂无
中图分类号
学科分类号
摘要
The influences of the dissimilarity in the roll speeds on the microstructure, texture and mechanical properties of 7075 aluminum plates produced via combined continuous casting and rolling (CCCR) process were investigated. Several experiments were conducted with three different upper/lower roll rotational speed ratios (ω/ω0, ω is the upper roll rotational speed and ω0 is the lower roll rotational speed), namely 1:1, 1:1.2 and 1:1.4. It was found that the greatest dissimilarity in the roll speed (ω/ω0=1:1.4) improved the yield strength and ultimate tensile strength of 7075 Al plate in the rolling direction by 41.5% and 21.9%, respectively. Moreover, at a roll speed ratio of ω/ω0=1:1.4, the average grain size was decreased by 36% whereas the mean hardness of the transverse cross-section of the finally rolled plate was increased by about 9.2%. Texture studies also revealed that the more the difference in the roll speeds was, the greater the isotropy and the hardness of the final product were. Nevertheless, conducting CCCR operation with different roll speeds resulted in about 6% reduction in the elongation of the deformed plate. © 2021 The Nonferrous Metals Society of China
引用
收藏
页码:901 / 912
相关论文
共 50 条
  • [41] Influence of Si Content on the Microstructure and Tensile Properties of Weathering Bridge Steel Produced via Thermal Mechanical Control Process
    Chen, Zhenye
    Shi, Genhao
    Qi, Jianjun
    Zhao, Liyang
    Liu, Yanli
    Wang, Qingfeng
    Wang, Guodong
    METALS, 2022, 12 (11)
  • [42] The Effect of Casting Speed and the Fraction of Al5%Ti1%B Inoculant on the Microstructure and Mechanical Properties of the AA5052 Aluminum Alloy Produced by the Direct Chill Process
    de Faria, Geraldo Lucio
    Leite, Anderson Santos
    MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS, 2018, 21 (02):
  • [43] Functionally Graded AA7075 Components Produced via Hot Stamping: A Novel Process Design Inspired from Analysis of Microstructure and Mechanical Properties
    Oecal, Ezgi Buetev
    Sajadifar, Seyed Vahid
    Sellner, Erik P. K.
    Vollmer, Malte
    Heidarzadeh, Akbar
    Zavasnik, Janez
    Niendorf, Thomas
    Groche, Peter
    ADVANCED ENGINEERING MATERIALS, 2023, 25 (15)
  • [44] Microstructure and Mechanical Properties of Ni-Coated Continuous Carbon Fibers-Reinforced Pure Aluminum Matrix Composites Prepared by Twin-Roll Casting Method
    Mu, Weipeng
    Lin, Jinbao
    Gong, Yi
    Wu, Dongxu
    Liu, Erqiang
    ADVANCED ENGINEERING MATERIALS, 2021, 23 (12)
  • [45] Influence of annealing on the microstructure and mechanical properties of Ti/steel clad plates fabricated via cold spray additive manufacturing and hot-rolling
    Zhao, Zhipo
    Tariq, Naeem ul Haq
    Tang, Junrong
    Ren, Yupeng
    Liu, Hanhui
    Tong, Min
    Yin, Lisong
    Du, Hao
    Wang, Jiqiang
    Xiong, Tianying
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 775
  • [46] Influence of Thermal Deformation Parameters on Mechanical Properties and Microstructure Evolution of AA7075 Aluminum Alloy during Hot Stamping-Quenching Process
    Huanhuan Li
    Zhili Hu
    Lin Hua
    Qian Sun
    JOM, 2019, 71 : 4778 - 4788
  • [47] Influence of Thermal Deformation Parameters on Mechanical Properties and Microstructure Evolution of AA7075 Aluminum Alloy during Hot Stamping-Quenching Process
    Li, Huanhuan
    Hu, Zhili
    Hua, Lin
    Sun, Qian
    JOM, 2019, 71 (12) : 4778 - 4788
  • [48] Microstructure and mechanical properties of 4045/3003/4045 aluminum alloy clad sheet fabricated by vertical-type high-speed tandem twin-roll casting
    Nakamura, Ryoji
    Tsutsui, Akari
    Haga, Toshio
    Harada, Yohei
    Kumai, Shinji
    Terayama, Kazuko
    Niikura, Akio
    Keikinzoku/Journal of Japan Institute of Light Metals, 2014, 64 (09): : 399 - 406
  • [49] Cold rolling and mechanical properties of unidirectionally solidified Al-Al3Ni strip produced by open type, horizontal, heated mold continuous casting process
    Kaneno, Yasuyuki
    Minami, Shigenari
    Shimizu, Toru
    Takasugi, Takayuki
    Keikinzoku/Journal of Japan Institute of Light Metals, 2000, 50 (12): : 671 - 675
  • [50] Microstructure evolution and mechanical properties of Cu-0.36Be-0.46Co alloy fabricated by heating-cooling combined mold horizontal continuous casting during cold rolling
    Jiang, Yan-bin
    Zhang, Tong-tong
    Lei, Yu
    Liu, Xin-hua
    Cao, Yang
    Xie, Jian-xin
    Zhao, Bing
    Li, Yong-hua
    Jiao, Chuan-rong
    TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2020, 30 (04) : 958 - 971