Rock stresses measurement with high stiffness hydraulic fracturing system in ILC kitakami site

被引：0
|
作者：
20161502219436
机构：
来源：
(1) OYO Corporation, Saitama, Japan; (2) Fukada Geological Institute, Tokyo, Japan; (3) Tohoku University, Sendai, Japan | 1600年 / International Society for Rock Mechanics期
关键词：
The hydraulic fracturing testing has the highest track record for techniques used in sub 1000 meter stress measurement. The predominant advantage of this method is that elastic constants such as Young's modulus and Poisson's ratio are not required for determining the value and direction of initial stress. The factors to determine the stress state are the water pressures of re-opening and shut-in of fractures around the borehole wall and its directions. With conventional methods; however; the accuracy of the derived stress states from the observation equations was often adversely affected by the lack of consideration of the remaining fluid pressure in fractures and insufficient stiffness of the pressurization system. We have developed a new hydraulic fracturing system based on a new test method concept overcoming these defects; and applied to a 300 meter deep borehole in granite. The most important improvement of the new system is an employment of a syringe pump that enables an accurate flow control of fluid with less than 1ml/min up to 30MPa. The new test system indicated pressure variations of the pressurized interval zone immediately after fluid injection; and the measured data was confirmed extremely accurate. Thus the rock stresses in ILC Kitakami site were determined quite accurately with our high stiffness hydraulic fracturing system. © 2014 by Japanese Committee for Rock Mechanics;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
118520
引用
收藏
相关论文
共 50 条
  • [1] Deep rock stress measurement by hydraulic fracturing method taking account of system compliance effect
    Ito, T.
    Satoh, T.
    Kato, H.
    ROCK STRESS AND EARTHQUAKES, 2010, : 43 - 49
  • [2] THREE DIMENSIONAL STRESS MEASUREMENT BY HYDRAULIC FRACTURING FOR DETERMINATION OF INITIAL ROCK STRESSES AND STRESS VARIATION INDUCED BY EXCAVATION.
    Mizuta, Yoshiaki
    Sano, Osamu
    Ogino, Shoji
    Ochiishi, Masanori
    Kato, Harumi
    Nihon Kogyokaishi, 1987, 103 (1188): : 75 - 85
  • [3] Direct Measurement of Rock Pressure in Mine Conditions by Hydraulic Fracturing Method
    O. P. Alekseenko
    A. M. Vaisman
    Journal of Mining Science, 2003, 39 : 475 - 481
  • [4] Direct measurement of rock pressure in mine conditions by hydraulic fracturing method
    Alekseenko, OP
    Vaisman, AM
    JOURNAL OF MINING SCIENCE, 2003, 39 (05) : 475 - 481
  • [5] Mechanical, hydraulic and seismological behavior of crystalline rock as a response to hydraulic fracturing at the grimsel test site
    2017, American Rock Mechanics Association (ARMA) (05):
  • [6] Stress determination from hydraulic fracturing tests: the system stiffness approach
    Raaen, AM
    Skomedal, E
    Kjorholt, H
    Markestad, P
    Okland, D
    INTERNATIONAL JOURNAL OF ROCK MECHANICS AND MINING SCIENCES, 2001, 38 (04) : 529 - 541
  • [7] Hydraulic fracturing stress measurement in underground salt rock mines at Upper Kama Deposit
    Rubtsova, E., V
    Skulkin, A. A.
    GEODYNAMICS AND STRESS STATE OF THE EARTH'S INTERIOR (GSSEI 2017), 2018, 134
  • [8] Hydraulic Fracturing-induced Seismicity at the Hot Dry Rock Site of the Gonghe Basin in China
    Chen Zubin
    Zhao Fa
    Sun Feng
    Lu Hao
    Wang Chunlu
    Wu Haidong
    Zhou Xiaohua
    ACTA GEOLOGICA SINICA-ENGLISH EDITION, 2021, 95 (06) : 1835 - 1843
  • [9] Hydraulic Fracturing-induced Seismicity at the Hot Dry Rock Site of the Gonghe Basin in China
    CHEN Zubin
    ZHAO Fa
    SUN Feng
    Lü Hao
    WANG Chunlu
    WU Haidong
    ZHOU Xiaohua
    Acta Geologica Sinica(English Edition), 2021, 95 (06) : 1835 - 1843
  • [10] Measurement and interpretation on in-situ stresses with hydro-fracturing in a highway tunnel site
    Yin, J.
    Chen, L.
    Zhong, Z.
    Jing, F.
    Lu, G.
    Yanshilixue Yu Gongcheng Xuebao/Chinese Journal of Rock Mechanics and Engineering, 2001, 20 (SUPPL.): : 1827 - 1830
12345