Post-processing ageing treatment of friction surfaced Al-16Si alloy: experimental and theoretical studies

被引：0
|
作者：
Bararpour, Seyedeh Marjan [1 ]
Jamshidi Aval, Hamed [1 ]
Jamaati, Roohollah [1 ]
Javidani, Mousa [2 ]
机构：
[1] Department of Materials Engineering, Babol Noshirvani University of Technology, Babol, Iran
[2] Department of Applied Science, University of Québec at Chicoutimi, Saguenay,QC, Canada
来源：
Materials Science and Technology (United Kingdom) | 2024年 / 40卷 / 05期
关键词：
D O I：
10.1177/02670836231214617
中图分类号：
学科分类号：
摘要：
In this study, we investigated the impact of ageing heat treatment following friction surfacing of a solid solution-treated Al-16Si alloy on coating geometry, microstructure, and wear resistance. We employed a simulation using the smoothed-particle hydrodynamics (SPH) method alongside experimental analysis. The simulation results revealed that as the rotational speed increased from 600 to 1000 rpm, the coating efficiency decreased significantly from 31.2 to 13.1%. When comparing the coating to the substrate and the consumable rod, it was seen that after ageing heat treatment, the wear rate of the coating made at a rotational speed of 600 rpm dropped by a lot, by 70% compared to the substrate and by 53% compared to the consumable rod. © Institute of Materials, Minerals and Mining 2024.
引用
收藏
页码：387 / 401
相关论文
共 24 条
  • [11] Tailoring microstructure of additive friction stir-deposited Al-Mg alloy through post-processing deformation treatment for enhancing mechanical performance
    Tang, Wenshen
    Yang, Xinqi
    Wang, Ruilin
    Luo, Ting
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2023, 885
  • [12] Enhancing the mechanical performance of Al–Zn–Mg alloy builds fabricated via underwater friction stir additive manufacturing and post-processing aging
    Changshu He
    Ying Li
    Jingxun Wei
    Zhiqiang Zhang
    Ni Tian
    Gaowu Qin
    Xiang Zhao
    Journal of Materials Science & Technology, 2022, 108 (13) : 26 - 36
  • [13] Effect of post heat treatment on fatigue behaviour of friction stir spot welded Al-Mg-Si alloy
    Pacific Industrial Co., Ltd., Japan
    不详
    Yosetsu Gakkai Ronbunshu, 2008, 1 (7-14):
  • [14] Enhancing the mechanical performance of Al-Zn-Mg alloy builds fabricated via underwater friction stir additive manufacturing and post-processing aging
    He, Changshu
    Li, Ying
    Wei, Jingxun
    Zhang, Zhiqiang
    Tian, Ni
    Qin, Gaowu
    Zhao, Xiang
    JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2022, 108 : 26 - 36
  • [15] Influence of post-processing techniques on the microstructure, properties and surface integrity of Al-Si-Mg alloy processed by laser powder bed fusion technique
    Subramaniyan, Anand Kumar
    Reddy, Anigani Sudarshan
    Mathias, Snehith
    Shrivastava, Abhishek
    Raghupatruni, Prasad
    SURFACE & COATINGS TECHNOLOGY, 2021, 425
  • [16] Effect of post-processing heat treatment on microstructure and microhardness of water-submerged friction stir processed 2219-T6 aluminum alloy
    Liu, H. J.
    Feng, X. L.
    MATERIALS & DESIGN, 2013, 47 : 101 - 105
  • [17] Effect of Post-Processing Treatment on Fatigue Performance of Ti6Al4V Alloy Manufactured by Laser Powder Bed Fusion
    Mancisidor, Ane Miren
    Garcia-Blanco, Maria Belen
    Quintana, Iban
    Arrazola, Pedro Jose
    Espinosa, Elixabete
    Cuesta, Mikel
    Albizuri, Joseba
    Garciandia, Fermin
    JOURNAL OF MANUFACTURING AND MATERIALS PROCESSING, 2023, 7 (04):
  • [18] Effect of post-heat treatment on the fatigue behaviour of a friction stir spot-welded Al-Mg-Si alloy
    Department of Mechanical and Systems Engineering, Gifu University, Gifu, Japan
    不详
    不详
    不详
    Weld. Int., 2009, 7 (481-489):
  • [19] Investigation of the effect of traverse speed in friction surfacing of Al–16Si alloy by smoothed-particle hydrodynamics (SPH) simulation and experimental study
    Seyedeh Marjan Bararpour
    Hamed Jamshidi Aval
    Roohollah Jamaati
    Mousa Javidani
    Computational Particle Mechanics, 2024, 11 : 339 - 357
  • [20] Surface hardening of an Al-Si-Cu-Ni-Mg aluminum alloy by friction stir processing and T6 heat treatment
    Khalikova, G. R.
    Zakirova, G. R.
    Farkhutdinov, A., I
    Korznikova, E. A.
    Trifonov, V. G.
    LETTERS ON MATERIALS, 2022, 12 (03): : 255 - 260
123