High-temperature aging property evaluation of lost circulation materials in deep and ultra-deep well drilling

被引：0

作者：

Kang Y. ^{[1
]}

Wang K. ^{[1
]}

Xu C. ^{[1
]}

You L. ^{[1
]}

Wang L. ^{[1
]}

Li N. ^{[2
]}

Li J. ^{[2
]}

机构：

[1] State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu, 610500, Sichuan

[2] PetroChina Tarim Oilfield Company, Korla, 841000, Xinjiang

来源：

Shiyou Xuebao/Acta Petrolei Sinica | 2019年 / 40卷 / 02期

关键词：

Bearing capacity; Formation damage; Fractured plugging zone; High temperature aging; Lost circulation control; Lost circulation material;

D O I：

10.7623/syxb201902010

中图分类号：

学科分类号：

摘要：

Drilling fluid losses always occur in deep and ultra-deep well drilling of fractured reservoirs, which will cause serious formation damage and significant economic losses. Drilling fluid losses often reoccur in the drilling of reservoir section, indicating the evaluation indexes of acid dissolution rate, particle size distribution and etc. for the conventional lost circulation material (LCM)are unable to meet the needs of lost circulation control. The walnut shells and millimeter-scale calcium carbonates often used in Kat gas reservoirs located in Tarim Basin are studied to conduct a high temperature aging experiment on LCM. Experimental evaluation indicates that the walnut shells stay at 180℃ diesel for 24 h, and their color change from yellow to black with the quality, friction coefficient and compressive strength reduced by 25.16%, 28.24% and 21.21% respectively. As the millimeter-calcium carbonates stay at 180℃ diesel for 24 h, their color changes from white to light yellow with the quality and friction coefficient reduced by 2.47% and 1.33% respectively, while their compressive strength is almost unchanged; The bearing capacity of the plugged zone formed by high temperature aged walnut shells and millimeter-scale calcium carbonates is reduced by 48.84%. The analysis demonstrates that the high temperature aging failure of LCM is an important factor for the structure destruction of fractured plugging zone and reoccurring losses in deep and ultra-deep well. © 2019, Editorial Office of ACTA PETROLEI SINICA. All right reserved.

引用

页码：215 / 223

页数：8

共 44 条

[21] Zeng Y., Li D., Yang C., Leakage prevention and control in fractured formations, Chinese Journal of Rock Mechanics and Engineering, 35, 10, pp. 2054-2061, (2016)
[22] Xu C., Kang Y., You L., Et al., Lost-circulation control for formation-damage prevention in naturally fractured reservoir: mathematical model and experimental study, SPE Journal, 22, 5, pp. 1654-1670, (2017)
[23] Qiu Z., Bao D., Liu J., Et al., Microcosmic mechanism of fracture-plugging instability and experimental study on pressure bearing and tight plugging, Acta Petrolei Sinica, 39, 5, pp. 587-596, (2018)
[24] Kemmish D.J., Hay J.N., The effect of physical ageing on the properties of Amorphous PEEK, Polymer, 26, 6, pp. 905-912, (1985)
[25] Ghazali N.A., Mohd T.A.T., Alias N., Et al., The effects of temperature on rheology properties and filtrate after using lemongrass as lost circulation materials for oil based drilling mud, Advanced Materials Research, 911, pp. 243-247, (2014)
[26] Li Z., Yang C., Ma P., Et al., Instrument for High temperature gel LCM evaluation, Drilling Fluid & Completion Fluid, 32, 2, pp. 52-54, (2015)
[27] Liu X., Timar M.C., Varodi A.M., Et al., An investigation of accelerated temperature-induced ageing of four wood species: colour and FTIR, Wood Science and Technology, 51, 2, pp. 357-378, (2017)
[28] Wang P., Li Z., Nie X., Et al., Anti-dilution properties of a special gel applied to loss circulation control in drilling, Acta Petrolei Sinica, 33, 4, pp. 697-701, (2012)
[29] Xu C., You Z., Kang Y., Et al., Stochastic modelling of particulate suspension transport for formation damage prediction in fractured tight reservoir, Fuel, 221, pp. 476-490, (2018)
[30] Bedrikovetsky P., You Z., Badalyan A., Et al., Analytical model for straining-dominant large-retention depth filtration, Chemical Engineering Journal, 330, pp. 1148-1159, (2017)

← 1 2 3 4 5 →