Effects of surface treatment on bonding properties and corrosion resistance of al-Li alloy

被引：0
|
作者：
Tu, Chui-Qian [1 ]
Li, Yi-Bo [2 ,3 ]
Huang, Ming-Hui [1 ,2 ,3 ]
Li, Jian [3 ]
Liu, Zhao-Wen [1 ]
Pei, Shi-Kai [3 ]
机构：
[1] Light Alloy Research Institute, Central South University, Changsha,410083, China
[2] State Key Laboratory of High Performance and Complex Manufacturing, Central South University, Changsha,410083, China
[3] College of Mechanical and Electrical Engineering, Central South University, Changsha,410083, China
来源：
Surface Technology | 2019年 / 48卷 / 12期
关键词：
Adhesive joints - Adhesives - Aluminum corrosion - Binary alloys - Chemical analysis - Chemical bonds - Corrosion resistance - Corrosion resistant alloys - Free energy - Lithium alloys - Morphology - Phosphoric acid - Surface morphology - Surface roughness - Surface treatment;
D O I：
10.16490/j.cnki.issn.1001-3660.2019.12.031
中图分类号：
学科分类号：
摘要：
The paper aims to improve the strength and corrosion resistance of aluminum-lithium alloy bonded joints. Surface treatments including sandpaper polishing, sandblasting and phosphoric acid anodizing were applied to Al-Li alloy. After surface treatment, a layer of FM94 adhesive was laid on the substrate and pressurized to cure to obtain a single lap joint. The surface properties of alloy samples including surface morphology, surface roughness, surface free energy and surface chemical composition were analyzed. The strength of the bonded joints before and after hot-humid exposure was tested, respectively to reveal the effects of different surface treatment methods on the strength and corrosion resistance of the bonded joints. Compared with sandpaper polished alloy samples, sandblasting and phosphoric acid anodizing treatments could significantly improve the surface roughness and surface free energy of aluminum-lithium alloy samples. At the same time, it was found by EDS analysis that the surface of the anodized alloy samples had a large amount of oxygen. The joint strength of anodized and sandblasted joints was 37.0 MPa and 26.8 MPa, respectively. However, that of sandpaper polished joints was only 16.4 MPa. After hot-humid exposure, the strength of phosphoric acid anodized joints was only decreased by 12.2%. However, the strength of joints after sandblasting and sanding treatment was decreased by 30.6% and 19.5%, respectively. Both anodizing and sand blasting surface treatments could increase the strength of the Al-li alloy bonded joint; however, the anodizing effect is better. The anodizing treatment can significantly enhance the corrosion resistance of the joint. However, the sandblasting treatment does not significantly improve the corrosion resistance of the joint. © 2019, Chongqing Wujiu Periodicals Press. All rights reserved.
引用
收藏
页码：257 / 263
相关论文
共 50 条
  • [31] Effect of aging treatment on the exfoliation corrosion and stress corrosion cracking behaviors of 2195 Al-Li alloy
    Wang, Xue-hui
    Wang, Ji-hui
    Yue, Xin
    Gao, Yun
    MATERIALS & DESIGN, 2015, 67 : 596 - 605
  • [32] Tailoring Al-Li Alloy Surface Wettability with a Femtosecond Laser and Its Effect on Bonding Performance
    Chen, Jun
    Li, Yibo
    Huang, Minghui
    Dong, Lei
    COATINGS, 2021, 11 (08)
  • [33] Effect of NaOH concentration on microstructure and corrosion resistance of MAO coating on cast Al-Li alloy
    Qin, Ying
    Wu, Guo-hua
    Atrens, Andrej
    Zhang, Xiao-long
    Zhang, Liang
    Ding, Wen-jiang
    TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2021, 31 (04) : 913 - 924
  • [34] MICROSTRUCTURE AND MECHANICAL PROPERTIES OF 8090 Al-Li ALLOY
    LIU Yulin ZHANG Yun ZHAO Hong’en HU Zhuangqi SHI Changxu Institute of Metal Research
    Acta Metallurgica Sinica(English Edition), 1992, (02) : 89 - 94
  • [35] Tem characterization of diffusion bonding of superplastic 8090 Al-Li alloy
    Urena, A
    deSalazar, JMG
    Quinones, J
    Martin, JJ
    SCRIPTA MATERIALIA, 1996, 34 (04) : 617 - 623
  • [36] Effect of solution treatment on microstructures and mechanical properties of 2099 Al-Li alloy
    Lin, Y.
    Zheng, Z. Q.
    Li, S. C.
    ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING, 2014, 14 (01) : 61 - 71
  • [37] Microstructure and mechanical properties of 8090 Al-Li alloy
    Liu, Yulin
    Zhang, Yun
    Zhao, Hongen
    Hu, Zhuangqi
    Shi, Changxu
    Acta Metallurgica Sinica Series A, Physical Metallurgy & Materials Science, 1992, 5 A (02): : 89 - 94
  • [38] Influence of Ce on the microstructure and properties of Al-Li alloy
    Wang, YX
    Xu, L
    ALUMINIUM ALLOYS: THEIR PHYSICAL AND MECHANICAL PROPERTIES, PTS 1-3, 1996, 217 : 1323 - 1328
  • [39] Mechanical properties and microstructure of 1460 Al-Li alloy
    Li J.
    Chen Y.
    Zhang X.
    Xu X.
    Zheng Z.
    Zhongnan Daxue Xuebao (Ziran Kexue Ban)/Journal of Central South University (Science and Technology), 2017, 48 (11): : 2866 - 2872
  • [40] Microstructure and properties of Al-Li alloy 2090 weldments
    Iamboliev, Theofil
    Schweissen und Schneiden/Welding and Cutting, 1999, 51 (06):
12345