Experimental and Theoretical Calculation of Bonding Performance between Threaded GFRP Bars and Concrete

被引：0
|
作者：
Song Z. [1 ]
Lu C. [1 ]
Xuan G. [1 ]
Cai Q. [1 ]
Bu S. [1 ]
机构：
[1] Faculty of Civil Engineering and Mechanics, Jiangsu University, Zhenjiang
来源：
Jianzhu Cailiao Xuebao/Journal of Building Materials | 2021年 / 24卷 / 04期
关键词：
Bonding performance; Glass fiber reinforced polymer(GFRP) bar; Pullout test; Strength prediction; Theoretical model;
D O I：
10.3969/j.issn.1007-9629.2021.04.029
中图分类号：
学科分类号：
摘要：
In order to study the bonding performance of the threaded glass fiber reinforced polymer(GFRP) bar and the concrete interface, three groups of pullout specimens were prepared from several GFRP bars of different diameters. A central pullout test was conducted on these specimens after 28d standard curing. Experimental results show that the bonding strength between GFRP bar and concrete increases as the bar diameter increases. The failure modes and bonding stress-slip curves of GFRP bars of different diameters change accordingly. For the GFRP bars with small diameters of 8mm and 12mm, the tested specimens are mainly pulled out and damaged, but the bonding stress-slip curves in the two cases also differ greatly after the stage of elastic rise. The test specimens of the diameter of 8mm tend to fluctuate back and forth, and gradually flatten. While the bonding stress of the pullout specimen with a bar of diameter of 12mm continues to rise and then decreases, showing a hyperbolic mode. When the diameter of GFRP bars becomes larger(16mm), the splitting damage appeares in the specimens tested. After the bonding stress-slip curve rises to the highest point, the bonding stress decreases rapidly. Finally, based on the theoretical model of the thick-walled cylinder of elastic mechanics, the angle of the bonding failure surface of the threaded GFRP bars of different diameters was discussed and the formula for calculating the bonding strength was proposed. The comparative analysis with the relevant test results verifies that the calculation formula has excellent prediction accuracy for specimens with pullout failure. © 2021, Editorial Department of Journal of Building Materials. All right reserved.
引用
收藏
页码：887 / 894
页数：7
相关论文
共 35 条
  • [1] FAN Xiangqian, LIU Jueding, HU Shaowei, Et al., Influence of FRP bonding length on fracture parameters of concrete three-point bending beam, Journal of Building Materials, 22, 1, pp. 38-44, (2019)
  • [2] RUAN X J, LU C H, XU K, Et al., Flexural behavior and serviceability of concrete beams hybrid-reinforced with GFRP bars and steel bars, Composite Structures, 235, (2020)
  • [3] YU T, ZHANG B, CAO Y B, Et al., Behavior of hybrid FRP-concrete-steel double-skin tubular columns subjected to cyclic axial compression, Thin-Walled Structures, 61, pp. 196-203, (2012)
  • [4] MOHAMMADALI R, VALTER C., A damage model for high-cycle fatigue behavior of bond between FRP brand concrete, International Journal of Fatigue, 111, pp. 101-111, (2018)
  • [5] MAO Weibing, ZHANG Dingguo, Pullout and bond properties of FRP reinforcing bars, Journal of Hohai University(Natural Science), 5, pp. 44-48, (2000)
  • [6] LU Shali, The research of surface structure effect on GFRP bar bond performance, (2016)
  • [7] ROBERT M, CUUSIN P, BENMOKRANE B., Durability of GFRP reinforcing bars embedded in moist concrete, Journal of Composites for Construction, 13, 2, pp. 66-73, (2009)
  • [8] ACHILLIDES Z, PILAKOUTAS K., Bond behavior of fiber reinforced polymer bars under direct pullout conditions, Journal of Composites for Construction, 8, 2, pp. 173-181, (2004)
  • [9] XU Xinsheng, Research on mechanical property of FRP bars and flexural property of concrete beams with FRP bars, (2007)
  • [10] HAO Qingduo, WANG Yanlei, HOU Jilin, Et al., Bond-slip constitutive model between GFRP/steel wire composite rebars and concrete, Engineering Mechanics, 26, 5, pp. 62-72, (2009)
1234