Properties of Alkali Activated Mortar Fresh and Hardened Properties Based on Fiber Reinforced Index

被引：0
|
作者：
Li L. [1 ,2 ,3 ]
Wei Y. [2 ]
Li Z. [1 ,2 ]
Zhang W. [3 ]
Shi D. [3 ]
Li D. [2 ]
机构：
[1] Key Laboratory of Agricultural Soil and Water Engineering in Arid and Semiarid Areas of Ministry of Education, Northwest A & F University, Xianyang
[2] College of Water Resources and Architectural Engineering, Northwest A & F University, Xianyang
[3] State Key Laboratory of Green Building Materials, Beijing
来源：
Kuei Suan Jen Hsueh Pao/Journal of the Chinese Ceramic Society | 2022年 / 50卷 / 08期
关键词：
Alkali-activated material; Fiber reinforced concrete; Fiber reinforcing index; Fractal dimension; Mechanical properties;
D O I：
10.14062/j.issn.0454-5648.20211188
中图分类号：
学科分类号：
摘要：
In order to explore the mechanism of action of fiber in alkali-activated materials, 26 groups of fiber reinforced alkali-activated mortar (FRAAM) were prepared at different length to diameter ratios, volume contents of polypropylene fiber (PPF) and water-binder ratios. The influence of fiber reinforced index (I) on the slump spread, flow rate, apparent density, ultrasonic wave velocity, compressive strength, bending strength, and crack fractal dimension of FRAAM was investigated. The results show that the effect of water-binder ratio on the plastic viscosity of FRAAM is more dominant than that on the yield stress. When I is less than critical I (Ic, i.e., 100), the influence of fibers is slight, the distance between fibers is far, and the workability of FRAAM is basically not affected. However, fibers are difficult to limit the cracking of mortar and improve its mechanical properties. When I is between Ic (i.e., 100) and dense I (Id, i.e., 350), the flexural strength, compressive strength and fracture fractal dimension of FRAAM improve, and the FRAAM can still flow freely under dead weight. When I is higher than Id (i.e., 350), significant fibrous clumps degrade the FRAAM workability, resulting in a poor compactness and a reduced compressive strength. The I thresholds of PPF-FRAAM are 100 and 350 for loose and tight packing, respectively, and the optimal volume fraction of PPF is between 100/(l/d) and 350/(l/d). © 2022, Editorial Department of Journal of the Chinese Ceramic Society. All right reserved.
引用
收藏
页码：2212 / 2220
页数：8
相关论文
共 35 条
  • [21] Standard Test Method for Pulse Velocity Through Concrete (ASTM C597-16), (2016)
  • [22] Test method of cement mortar strength (ISO method) (in Chinese), (1999)
  • [23] CAO M, ZHANG C, LV H., Mechanical response and shrinkage performance of cementitious composites with a new fiber hybridization, Constr Build Mater, 57, pp. 45-52, (2014)
  • [24] KRIEGER I M, DOUGHERTY T J., A Mechanism for Non-Newtonian Flow in Suspensions of Rigid Spheres, Trans Soc Rheol, 3, 1, pp. 137-152, (1959)
  • [25] PHILIPSE A P., The random contact equation and its implications for (colloidal) rods in packings, suspensions, and anisotropic powders, Langmuir, 12, 5, pp. 1127-1133, (1996)
  • [26] CAO M, LI L., New models for predicting workability and toughness of hybrid fiber reinforced cement-based composites, Constr Build Mater, 176, pp. 618-628, (2018)
  • [27] CAO M, LI L, SHEN S., Influence of reinforcing index on rheology of fiber-reinforced mortar, ACI Mater J, 116, 6, pp. 95-105, (2019)
  • [28] LI L, CAO M., Influence of calcium carbonate whisker and polyvinyl alcohol-steel hybrid fiber on ultrasonic velocity and resonant frequency of cementitious composites, Constr Build Mater, 188, pp. 737-746, (2018)
  • [29] AYDIN S, BARADAN B., The effect of fiber properties on high performance alkali-activated slag/silica fume mortars, Compos Part B: Eng, 45, 1, pp. 63-69, (2013)
  • [30] SHI C, XIE P., Interface between cement paste and quartz sand in alkali-activated slag mortars, Cem Concr Res, 28, 6, pp. 887-896, (1998)
1234