Influence of Spinning Deformation on Microstructures and Tensile Properties of B4C Particulate Reinforced Aluminium Matrix Composite Tube

被引：0

作者：

Chen, Hongsheng ^{[1
,2
,3
]}

Sun, Tianming ^{[1
]}

Wang, Wenxian ^{[1
,2
,3
]}

Nie, Huihui ^{[1
]}

Zhang, Peng ^{[1
]}

Liu, Run'ai ^{[1
]}

Yang, Tao ^{[1
]}

Zhang, Yuanqi ^{[1
]}

机构：

[1] Taiyuan University of Technology, College of Mechanical and Vehicle Engineering, College of Physics and Photo Electricity Engineering, Taiyuan,030024, China

[2] Shanxi Key Laboratory of Advanced Magnesium-based Materials, Taiyuan,030024, China

[3] Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan,030024, China

来源：

Xiyou Jinshu Cailiao Yu Gongcheng/Rare Metal Materials and Engineering | 2019年 / 48卷 / 09期

关键词：

Boron carbide - Tensile strength - Aluminum - Spark plasma sintering - Electric discharges - Aluminum compounds;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

The B4C particles reinforced aluminium matrix composite tube with different deformation was fabricated by spark plasma sintering (SPS) followed by asynchronous offset spinning. The effects of deformation on microstructure and mechanical properties of the composite tube were investigated. Results show that distribution of the B4C particles changes from net-like to relatively homogeneous in the aluminium matrix with the spun deformation increasing. Metallurgical bonding forms on the interface between B4C and aluminium; the local high temperature of the interface between particles caused by the top discharge between particles during SPS processing promotes the interface bonding. The interface mainly consists of AlB2 and Al3BC phase. With the deformation increasing, the aluminium grain and B4C particle are decreased in size. However, the large sized B4C particle fracture weakens the function of the fine-grain strengthening and particles strengthening for the tensile strength. © 2019, Science Press. All right reserved.

引用

页码：2923 / 2929

共 50 条

[21] Microstructure and Dry-Sliding Wear Behavior of B4C Ceramic Particulate Reinforced Al 5083 Matrix Composite
Zhao, Qian
Liang, Yunhong
Zhang, Zhihui
Li, Xiujuan
Ren, Luquan
METALS, 2016, 6 (09):
[22] Processing and mechanical properties of B4C reinforced Al matrix composites
Topcu, I.
Gulsoy, H. O.
Kadioglu, N.
Gulluoglu, A. N.
JOURNAL OF ALLOYS AND COMPOUNDS, 2009, 482 (1-2) : 516 - 521
[23] Processing and mechanical properties of B4C reinforced Al matrix composites
Topcu, I.
Gulsoy, H.O.
Kadioglu, N.
Gulluoglu, A.N.
Journal of Alloys and Compounds, 2009, 482 (1-2): : 516 - 521
[24] Evaluation of heat damage on B4C particulate reinforced aluminum alloy matrix composite using acoustic emission techniques
Nayeb-Hashemi, H
Shan, D
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1999, 266 (1-2): : 8 - 17
[25] Fabrication of B4C participate reinforced magnesium matrix composite by powder metallurgy
Jiang, Q.C. (jiangqc@mail.jlu.edu.cn), 1600, Elsevier Ltd (386): : 1 - 2
[26] Effect of volume fraction and size of B4C particles on production and microstructure properties of B4C reinforced aluminium alloy composites
Canakci, A.
Arslan, F.
Varol, T.
MATERIALS SCIENCE AND TECHNOLOGY, 2013, 29 (08) : 954 - 960
[27] Prediction of tensile strength of friction stir welded aluminium matrix TiCp particulate reinforced composite
Gopalakrishnan, S.
Murugan, N.
MATERIALS & DESIGN, 2011, 32 (01) : 462 - 467
[28] Tensile properties of TiC particulate reinforced titanium matrix composite at elevated temperature
Zhang Tingjie
Zhang Xiaoming
Mao Xiaonan
Zeng Liying
Li Qingyu
JOURNAL OF ADVANCED MATERIALS, 2007, : 5 - 8
[29] Investigation of Dry Sliding Wear Behaviour of B4C Particulate Reinforced Mg Matrix Composites
Guleryuz, L. Feray
Ozan, S.
Uzunsoy, D.
Ipek, R.
ACTA PHYSICA POLONICA A, 2013, 123 (02) : 488 - 489
[30] Cold spraying B4C particles reinforced aluminium coatings
Huang, Guosheng
Fu, Wei
Ma, Li
Li, Xiangbo
Wang, Hongren
SURFACE ENGINEERING, 2019, 35 (09) : 772 - 783

← 1 2 3 4 5 →