Influence of bias voltage on microstructure and properties of AlTiSiN nanocomposite coatings prepared by MPP

被引:0
|
作者
Bin-Hua, Gui [1 ]
Hui, Zhou [1 ]
Jun, Zheng [1 ]
Zhan-Ji, Ma [1 ]
La-Mao-cao, Yang [1 ]
Yan-Shuai, Zhang [1 ]
机构
[1] Science and Technology on Vacuum Technology and Physics Laboratory, Lanzhou Institute of Physics, Lanzhou,730000, China
来源
Surface Technology | 2020年 / 49卷 / 01期
关键词
Aluminum compounds - Bias voltage - Chromium compounds - Composite coatings - Magnetron sputtering - Morphology - Nanocomposite films - Nanocomposites - Silicon compounds - Substrates - Surface morphology - Surface roughness - Tribology - Wear of materials;
D O I
10.16490/j.cnki.issn.1001-3660.2020.01.027
中图分类号
学科分类号
摘要
The work aims to regulate the microstructure and optimize the mechanical properties of AlTiSiN nano-composite coatings. AlTiSiN nanocomposite coatings were deposited through Modulated Pulsed Power Magnetron Sputtering by varying the substrates bias voltage from-50 V to-250 V. XRD, SEM, EDS, AFM, film comprehensive performance tester and ball and disc friction tester were used to test the microstructure, composition, surface morphology, mechanical and tribological properties. From the results, the influence of bias voltage on element composition was not obvious. For microstructure, the diffraction peaks on the crystal face of AlTiSiN coatings prepared under different bias voltage broadened obviously and nano-crystalline appeared. The diffraction peak on the crystal face of the coating prepared under the condition of-200 V was in the shape of steamed bread peak, which indicated that the crystallization property of the coating was obviously reduced, and the coating had an amorphous-like structure. When the bias voltage rose to-250 V, the high energy ions bombarded the growth surface of the coating continuously, causing the growth surface of the coating to heat up obviously and resulting in obvious improvement of crystallization performance. The surface of the coating was smooth and compact, with the surface roughness as low as 1.753 nm. For mechanical property, with the increase of substrate bias, the hardness of the coating gradually decreased after reaching the maximum value. The maximum hardness and H/E* ratio were 25.9 GPa and 0.13, respectively. As for the wear properties, the lowest wear rate of 4.7×10-15 m3/(N.m) could be achieved when the bias voltage was-200 V. Changing the substrate bias can effectively regulate the microstructure of the coatings and then optimize the microstructure, mechanical properties and tribological properties of the coatings. © 2020, Chongqing Wujiu Periodicals Press. All rights reserved.
引用
收藏
页码:228 / 236
相关论文
共 50 条
  • [41] Influence of deposition voltage on phases and microstructure of hydroxyapatite coatings prepared on C-C composites by hydrothermal electrodeposition
    Huang, J. F.
    Zhu, G. Y.
    Cao, L. Y.
    Wu, J. P.
    He, H. Y.
    MATERIALS TECHNOLOGY, 2007, 22 (02) : 88 - 90
  • [42] Mechanical properties and microstructure of TiC/amorphous hydrocarbon nanocomposite coatings
    Meng, WJ
    Tittsworth, RC
    Rehn, LE
    THIN SOLID FILMS, 2000, 377 : 222 - 232
  • [43] Microstructure and mechanical properties of a-CNx films prepared by bias voltage assisted PLD with carbon nitride target
    Zheng, Xiao-hua
    Yang, Fang-er
    Chen, Li
    Chen, Zhan-ling
    Song, Ren-guo
    Zhang, Xiang-hua
    SURFACE & COATINGS TECHNOLOGY, 2014, 258 : 716 - 721
  • [44] Effect of bias voltage polarity of a substrate on the texture, microstructure, and magnetic properties of Ni films prepared by magnetron sputtering
    Dzhumaliev, A. S.
    Nikulin, Yu. V.
    Filimonov, Yu. A.
    PHYSICS OF THE SOLID STATE, 2016, 58 (06) : 1247 - 1256
  • [45] Effect of bias voltage polarity of a substrate on the texture, microstructure, and magnetic properties of Ni films prepared by magnetron sputtering
    A. S. Dzhumaliev
    Yu. V. Nikulin
    Yu. A. Filimonov
    Physics of the Solid State, 2016, 58 : 1247 - 1256
  • [46] Effect of bias voltage on microstructure of DC magnetron sputtered Al coatings on uranium
    Lü, XC
    Wang, XL
    Lang, DM
    Dong, P
    TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2004, 14 : 247 - 250
  • [47] Effects of substrate bias voltage on the microstructure of Cr-Al-N coatings
    Zhu, Ming
    Duo, Shuwang
    Li, Tianpeng
    Li, Meishuan
    Zhou, Yanchun
    SURFACE ENGINEERING (ICSE 2007), 2008, 373-374 : 167 - +
  • [48] Effect of voltage on microstructure and its influence on corrosion and tribological properties of TiO2 coatings
    Dhiflaoui, Hafedh
    Khlifi, Kaouther
    Barhoumi, Najoua
    Larbi, Ahmed Ben Cheikh
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2020, 9 (03): : 5293 - 5303
  • [49] Effects of Bias Voltage on Properties of (Ti, Al) N Coatings
    Chen Tao
    Wu Hua
    Wang Qing-hui
    MECHANICAL ENGINEERING, MATERIALS AND ENERGY II, 2013, 281 : 426 - 429
  • [50] Influence of negative bias voltage and deposition temperature on microstructure and properties of superhard TiB2 coatings deposited by high power impulse magnetron sputtering
    Zhang, Teng Fei
    Gan, Bin
    Park, Seong-mo
    Wang, Qi Min
    Kim, Kwang Ho
    SURFACE & COATINGS TECHNOLOGY, 2014, 253 : 115 - 122