Research on Continuous Shear Calendering Process and Performance of Modified Double-base Propellant Substitute Materials with High Solid Content

被引：0

作者：

Liang L. ^{[1
]}

Ji J. ^{[1
]}

Yang X.-Q. ^{[2
]}

Huang D.-Y. ^{[2
]}

Liu Y.-Z. ^{[2
]}

Liao X. ^{[1
]}

Guo X.-D. ^{[1
]}

机构：

[1] School of Chemical Engineering, Nanjing University of Science and Technology, Nanjing

[2] Shanxi North Xing'an Chemical Industry Co. Ltd., Taiyuan

来源：

Huozhayao Xuebao/Chinese Journal of Explosives and Propellants | 2021年 / 44卷 / 03期

关键词：

Modified double-base propellant; Performance analysis; Propellant with high solid content; Shear roll mills; Simulated materials;

D O I：

10.14077/j.issn.1007-7812.202104013

中图分类号：

学科分类号：

摘要：

In order to understand the characteristics of continuous shear calendering process for modified double-base propellant with high solid content, a high-solid substitute material with solid filler mass fraction of 30%-50% was used for the experiment. The state of the material, temperature distribution and water content of the simulated materials were studied. And the micromixing effect and the degree of plasticization were tested by SEM and DSC, respectively. The results show that with the increase of solid content, it becomes worse for the material sticking to the roll at the feed part, but better on the rear part. Meanwhile, the temperature of the roll surface and the water content decrease. Under the same solid content, the introduction of Al powder will increase the temperature of the material on the roll surface and make the water content of the sample decrease slightly. The higher the solid content, the greater the viscosity of the simulated material. And the viscosity of samples containing Al is greater than that without Al. SEM test and calcination test show that the materials are evenly distributed and mixed well. The plasticization degree of the system decreases with the increase of solid content, and is slightly affected by the solid composition. For propellants with high solid content, especially containing Al powder, it is recommended to reduce the calendering temperature appropriately. © 2021, Editorial Board of Journal of Explosives & Propellants. All right reserved.

引用

页码：328 / 335

页数：7

共 20 条

[11] (2005)
[12] JIAO Qing-jie, LI Jiang-cun, REN Hui, Et al., Effect of RDX particle size on properties of CMDB propellant, Chinese Journal of Energetic Materials, 15, 3, pp. 220-223, (2007)
[13] WANG Han, FAN Xue-zhong, ZHOU Wen-jing, Et al., Surface and interface properties of less smoke composite modified double-base propellant containing nitramine and aluminium, Chinese Journal of Explosives & Propellants (Huozhayao Xuebao), 34, 6, pp. 64-68, (2011)
[14] GEVGILILI H, KALYON D M, SHAH A., Processing of gun propellants in continuous shear roll mills, Journal of Energetic Materials, 26, 1, pp. 29-51, (2007)
[15] ELBASUNEY S, FAHD A., Combustion wave of metalized extruded double-base propellants, Fuel, 237, pp. 1274-1280, (2019)
[16] ELBASUNEY S, FAHD A, MOSTAFA H E., Combustion characteristics of extruded double base propellant based on ammonium perchlorate/aluminum binary mixture, Fuel, 208, pp. 296-304, (2017)
[17] MALLORY J, DEFINI S J, SOJKA P., Formulation of gelled propellant simulants, 46th AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit, (2010)
[18] WU Jing-an, Investigation of the working principle of CMS-roler, Plastics, 26, 3, pp. 33-37, (1997)
[19] PENG Zhao-yu, XUE Ping, SONG Xiu-duo, Et al., Effect of solid content on calendered plasticizing properties of solid propellants substitute materials, Journal of Solid Rocket Technology, 3, pp. 302-309, (2020)
[20] WU Qiao-hui, MA Mei, HU Xing-jun, Study on plasticizing degree of RPVC heat processing process with DSC technology, Synthetic Materials Aging and Application, 39, 4, pp. 11-13, (2010)

← 1 2 →