Progress in Additive Manufacturing on Complex Structures and High-performance Materials

被引：15
|
作者：
Liu W. [1 ]
Li N. [1 ]
Zhou B. [1 ]
Zhang G. [1 ]
Liang J. [1 ]
Zheng T. [1 ]
Xiong H. [1 ]
机构：
[1] 3D Printing Research & Engineering Technology Center, AECC Beijing Institute of Aeronautical Materials, Beijing
来源：
Jixie Gongcheng Xuebao/Journal of Mechanical Engineering | 2019年 / 55卷 / 20期
关键词：
Additive manufacturing; Arc; Complex structures; Electron beam; High-performance materials; Laser;
D O I：
10.3901/JME.2019.20.128
中图分类号：
学科分类号：
摘要：
With the characteristics of point by point melting and layer by layer manufacturing, additive manufacturing (AM), on one hand, can fabricate the three-dimensional complex structure parts rapidly; on the other hand, it can realize the high performance of materials. Based on the technological advantages and important application prospects of AM technology, the recent efforts and advances in AM on complex structures including:lattice structures, large thin-walled structures, complex surface structures, integrated structures; and materials including:iron-based alloys, titanium-based alloys, nickel-based alloys, aluminum-based alloys, intermetallic compounds, functionally gradient materials, ceramics are presented and reviewed. The development trend of AM on structure design, special materials system, new materials, repairing and remanufacturing, data base and standards are also forecasted. © 2019 Journal of Mechanical Engineering.
引用
收藏
页码：128 / 151and159
相关论文
共 164 条
  • [71] Cao F., Jia Y., Prashanth K.G., Et al., Evolution of microstructure and mechanical properties of as-cast Al-50Si alloy due to heat treatment and P modifier content, Materials & Design, 74, pp. 150-156, (2015)
  • [72] Vora P., Mumtaz K., Todd I., Et al., AlSi12 in-situ alloy formation and residual stress reduction using anchorless selective laser melting, Additive Manufacturing, 7, pp. 12-19, (2015)
  • [73] Thijs L., Kempen K., Kruth J.P., Et al., Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder, Acta Materialia, 61, 5, pp. 1809-1819, (2013)
  • [74] Kempen K., Thijs L., Yasa E., Et al., Process Optimization and Microstructural Analysis for Selective Laser Melting of AlSi10Mg, Solid Freeform Fabrication Symposium, 22, pp. 484-495, (2011)
  • [75] Louvis E., Fox P., Sutcliffe C.J., Selective laser melting of aluminium components, Journal of Materials Processing Technology, 211, 2, pp. 275-284, (2011)
  • [76] Zhao G., Wang D., Bai P., Et al., Progress in laser rapid prototyping technology for aluminium alloys, Hot Processing Technology, 39, 9, pp. 170-173, (2010)
  • [77] Brice C.A., Dennis N., Cooling rate determination in additively manufactured aluminum alloy 2219, Metallurgical and Materials Transactions A, 46, 5, pp. 2304-2308, (2015)
  • [78] Brice C., Shenoy R., Kral M., Et al., Precipitation behavior of aluminum alloy 2139 fabricated using additive manufacturing, Materials Science and Engineering: A, 648, pp. 9-14, (2015)
  • [79] Yu J., Aluminum-based materials for electron beam 3D printing and their formability, (2018)
  • [80] Gu J.L., Ding J.L., Cong B.Q., Et al., The influence of wire properties on the quality and performance of wire+arc additive manufactured aluminium parts, Advanced Materials Research, 8, pp. 210-214, (2014)
3456789101112