RESEARCH REGARDING THE EVOLUTION OF TEMPERATURE IN CASE OF DRY TURNING OF AN ALUMINUM ALLOY

被引：0
|
作者：
Trif, Adrian [1 ]
Nedezki, Claudiu Mihai [2 ]
机构：
[1] Tech Univ Cluj Napoca, Dept Mfg Engn, Cluj Napoca, Romania
[2] Tech Univ Cluj Napoca, Dept Engn & Robot, Cluj Napoca, Romania
来源：
ACTA TECHNICA NAPOCENSIS SERIES-APPLIED MATHEMATICS MECHANICS AND ENGINEERING | 2015年 / 58卷 / 04期
关键词：
temperature; turning; deform; cutting tools;
D O I：
暂无
中图分类号：
O3 [力学];
学科分类号：
08 ; 0801 ;
摘要：
The purpose of this paper is to analyze the influence of the temperature in case of dry turning of an aluminum alloy. The measured temperature in turning process was compared with the temperature obtained after the simulation using DEFORM 2D software.
引用
收藏
页码：547 / 552
页数：6
相关论文
共 50 条
  • [21] Optimization of cutting parameters for finish turning of 6082-T6 aluminum alloy under dry and RQL conditions
    Rafael F. Garcia
    Everton C. Feix
    Henrique T. Mendel
    Arnaldo R. Gonzalez
    André J. Souza
    Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2019, 41
  • [22] Effect of deformation temperature on microstructure evolution in 2219 aluminum alloy during ECAP
    Mazurina, I.
    Sitdikov, O.
    Kaibyshev, R.
    Miura, H.
    Sakai, T.
    RECRYSTALLIZATION AND GRAIN GROWTH III, PTS 1 AND 2, 2007, 558-559 : 545 - +
  • [23] An optimization investigation on surface roughness and its evolution with tool wear in dry turning of boron alloy cast iron
    An, Qinglong
    Xu, Jinyang
    Wei, Yingying
    Chen, Ming
    INDIAN JOURNAL OF ENGINEERING AND MATERIALS SCIENCES, 2014, 21 (06) : 601 - 608
  • [24] Research on Semisolid Microstructural Evolution of 2024 Aluminum Alloy Prepared by Powder Thixoforming
    Li, Pubo
    Chen, Tijun
    Zhang, Suqing
    Guan, Renguo
    METALS, 2015, 5 (02): : 547 - 564
  • [25] Research of Damage Evolution of 2219 Aluminum Alloy Weld Hole Based on ANSYS
    Zhang, Ping
    Yu, Xiao
    Li, Yuanyuan
    Wang, Youqiang
    PROCEEDINGS OF THE 2017 INTERNATIONAL CONFERENCE ON MATERIAL SCIENCE, ENERGY AND ENVIRONMENTAL ENGINEERING (MSEEE 2017), 2017, 125 : 60 - 67
  • [26] Analysis of the Elements of Secondary Adhesion Wear in Dry Turning of Aluminum Alloys
    Batista, M.
    Salguero, J.
    Gomez, A.
    Alvarez, M.
    Marcos, M.
    4TH MANUFACTURING ENGINEERING SOCIETY INTERNATIONAL CONFERENCE (MESIC 2011), 2012, 1431 : 366 - 373
  • [27] Research on Temperature Characteristics of Fiber Bragg Grating Sensors with Aluminum Alloy Packaging
    Du, Cuicui
    Kong, Deren
    Xu, Chundong
    Zhang, Xuehui
    INTERNATIONAL CONFERENCE ON SENSORS AND INSTRUMENTS (ICSI 2021), 2021, 11887
  • [28] Turning Machinability of SiC Particle Reinforced Aluminum Alloy Composites
    Asano, Kazunori
    Liu, Jinrong
    Fujita, Takashi
    Hayashi, Mutsuo
    Katsumata, Shuhei
    Ochiai, Shogo
    MATERIALS TRANSACTIONS, 2025, 66 (03) : 376 - 382
  • [29] EFFECT OF SILICON CONTENT OF ALUMINUM ALLOY 6351 IN TURNING PROCESS
    da Cunha, Daniel Fernandes
    da Silva, Marcio Bacci
    INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION - 2012, VOL 3, PTS A-C: DESIGN, MATERIALS, AND MANUFACTURING, 2013, : 1959 - 1967
  • [30] Evaluation and Performance Improvement of Environmentally Friendly Sustainable Turning of 6063 Aluminum Alloy in Dry Conditions Using Grey Relational Analysis
    Kannan, A.
    Sivaram, N. M.
    INTERNATIONAL JOURNAL OF AUTOMOTIVE AND MECHANICAL ENGINEERING, 2024, 21 (01) : 11085 - 11098
12345