A Study of Micro-EDM on Silicon Nitride Using Electrode Materials

被引：0
|
作者：
Muttamara, Apiwat [1 ]
Janmanee, Pichai [1 ,2 ]
Fukuzawa, Yasushi [3 ]
机构：
[1] Thammasat Univ, Dept Ind Engn, Fac Engn, Bangkok, Thailand
[2] Rajamangala Univ Technol Krungthep, Dept Ind Engn, Bangkok, Thailand
[3] Nagaoka Univ Technol, Dept Mech Engn, Fac Engn, Nagaoka, Niigata, Japan
来源：
INTERNATIONAL TRANSACTION JOURNAL OF ENGINEERING MANAGEMENT & APPLIED SCIENCES & TECHNOLOGIES | 2010年 / 1卷 / 01期
关键词：
Electrical discharge machining (EDM); Microelectrodes Wear; electrode wear ratio (EWR); Micro-EDM;
D O I：
暂无
中图分类号：
O [数理科学和化学]; P [天文学、地球科学]; Q [生物科学]; N [自然科学总论];
学科分类号：
07 ; 0710 ; 09 ;
摘要：
This research proposes Cu, CuW and AgW for electrode materials for micro-electro-discharge machining (micro-EDM), which are produced with block electrode on insulating Si3N4. With these electrodes, some trials were evaluated considering the EDM conditions. The machining properties were estimated by the removal rate and tool wear ratio. The same phenomena are applied at the micron level for micro machining. The conductive layer was investigated on the micro-hole. This study aimed at the minimum of discharge energy to generate the conductive layer resulting to success micro-EDM on insulating ceramics. (C) 2010 International Transaction Journal of Engineering, Management, & Applied Sciences & Technologies. Some Rights Reserved.
引用
收藏
页码：1 / 7
页数：7
相关论文
共 50 条
  • [1] Investigations on reduction of tool electrode wear in micro-EDM using novel electrode materials
    Uhlmann, Eckart
    Roehner, Markus
    CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2008, 1 (02) : 92 - 96
  • [2] A simulation study on rod electrode wear in Micro-EDM
    Wang, Hu
    Wang, Yuangang
    Wu, Menghua
    Li, Xiaopeng
    Liu, Yu
    ADVANCED MANUFACTURING TECHNOLOGY, PTS 1-4, 2012, 472-475 : 2426 - +
  • [3] Effects of Electrode and Workpiece Materials on the Sustainability of Micro-EDM Drilling Process
    Gianluca D’Urso
    Claudio Giardini
    Chiara Ravasio
    International Journal of Precision Engineering and Manufacturing, 2018, 19 : 1727 - 1734
  • [4] Effects of Electrode and Workpiece Materials on the Sustainability of Micro-EDM Drilling Process
    D'Urso, Gianluca
    Giardini, Claudio
    Ravasio, Chiara
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2018, 19 (11) : 1727 - 1734
  • [5] Study on Influence of Electrode Material on Hole Drilling in Micro-EDM
    Fu, Yulei
    Miyamoto, Takumu
    Natsu, Wataru
    Zhao, Wansheng
    Yu, Zuyuan
    18TH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM XVIII), 2016, 42 : 516 - 520
  • [6] Effect of Electrode Size on the Performances of Micro-EDM
    Liu, Qingyu
    Zhang, Qinhe
    Zhu, Guang
    Wang, Kan
    Zhang, Jianhua
    Dong, Chunjie
    MATERIALS AND MANUFACTURING PROCESSES, 2016, 31 (04) : 391 - 396
  • [7] INVESTIGATION ON ELECTRODE WEAR IN MICRO-EDM DRILLING
    Pellegrini, G.
    Ravasio, C.
    MM SCIENCE JOURNAL, 2024, 2024 : 7619 - 7625
  • [8] Experimental study of micro-EDM machining performances on silicon wafer
    Song, XZ
    Meeusen, W
    Reynaerts, D
    Van Brussel, H
    MICROMACHINING AND MICROFABRICATION PROCESS TECHNOLOGY VI, 2000, 4174 : 331 - 339
  • [9] A study on electrode wear sensing and compensation in Micro-EDM using machine vision system
    Yan, Mu-Tian
    Huang, Kuo-Yi
    Lo, Chin-Yen
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2009, 42 (11-12): : 1065 - 1073
  • [10] A study on electrode wear sensing and compensation in Micro-EDM using machine vision system
    Mu-Tian Yan
    Kuo-Yi Huang
    Chin-Yen Lo
    The International Journal of Advanced Manufacturing Technology, 2009, 42 : 1065 - 1073
12345