HEAT-TRANSFER ANALYSIS DURING WATER SPRAY COOLING OF STEEL RODS

被引：53

作者：

MORALES, RD ^{[1
]}

LOPEZ, AG ^{[1
]}

OLIVARES, IM ^{[1
]}

机构：

[1] HYLSA SN,PUEBLA STEELWORKS,MIGUEL XOXTLA,PUEBLA,MEXICO

来源：

ISIJ INTERNATIONAL | 1990年 / 30卷 / 01期

关键词：

cooling-rate reheating; drawing; finishing mill; flow-rate; heat-transfer; pearlitic transformation; rod; speed; steel; Stelmor Process; water-spray; wire;

D O I：

10.2355/isijinternational.30.48

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

A mathematical model has been developed to predict the rod cooling behavior of steel rods under the action of water sprays in the precooling system of a Stelmor machine. The main objective of this work was to study the influence of operation parameters such as rod size, rod speed, rod temperature at the finishing mill, water flow-rate and spray cooling sequence on the final temperature distribution within the rod before it enters into the transformation conveyor. This heat transfer analysis indicates that the spray cooling sequence affects, considerably, the temperature distribution inside the rod. Besides, water flow-rate failures in the spray cooling system disturb drastically its cooling efficiency. Finally, reheating phenomena which go from 150 to 200°C at rod surface are predicted. The calculations were validated with in situ experimental measurements carried out at HyLSA's (Puebla Plant) Stelmor machine. Very good agreement was found between predicted and experimentally measured rod surface temperatures. © 1990, The Iron and Steel Institute of Japan. All rights reserved.

引用

页码：48 / 57

页数：10

共 50 条

[41] SURFACE-ROUGHNESS AND ITS EFFECTS ON THE HEAT-TRANSFER MECHANISM OF SPRAY COOLING
MESLER, R
JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME, 1993, 115 (04): : 1083 - 1083
[42] Identification of heat flux and heat transfer coefficient during water spray cooling of horizontal copper plate
Cebo-Rudnicka, Agnieszka
Malinowski, Zbigniew
INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2019, 145
[43] HEAT-TRANSFER WITH THE COOLING OF A PLANE VERTICAL SURFACE BY JETS OF WATER
ISACHENKO, VP
SIDOROVA, IK
NIKOLAEVA, OS
THERMAL ENGINEERING, 1983, 30 (03) : 165 - 167
[44] Heat transfer of a stationary steel plate during water jet impingement cooling
Nobari, Amir Hossein
Prodanovic, Vladan
Militzer, Matthias
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2016, 101 : 1138 - 1150
[45] Spray Cooling Heat Transfer - Test and CFD Analysis
Ortloff, Charles R.
Vogel, Marlin
2011 27TH ANNUAL IEEE SEMICONDUCTOR THERMAL MEASUREMENT AND MANAGEMENT SYMPOSIUM (SEMI-THERM), 2011, : 245 - 252
[46] Estimating surface heat flux of spray cooling by inverse heat-transfer computation and sparse regression
Li, Min
Wu, Youjian
Wen, Zhexi
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2024, 152
[47] Spray Cooling Heat Transfer and Calculation of Water Impact Density for Cooling of Steel Sheet Materials by Inverse Process Modelling
Wendelstorf, J.
Wendelstorf, R.
Spitzer, K. -H.
STEEL RESEARCH INTERNATIONAL, 2009, 80 (09) : 639 - 644
[48] HEAT-TRANSFER IN SPRAY OF MECHANICAL ATOMIZERS
SHUVALOV, VV
GALUSTOV, VS
THERMAL ENGINEERING, 1974, 21 (11) : 116 - 120
[49] Determination of heat transfer coefficents during spray cooling by measuring spray characteristics
Krause, C.
Gretzki, T.
Nuernberger, F.
Schaper, M.
Bach, F. -W.
FORSCHUNG IM INGENIEURWESEN-ENGINEERING RESEARCH, 2006, 70 (04): : 237 - 242
[50] DETERMINING THE HEAT-TRANSFER COEFFICIENTS DURING COOLING OF LARGE PIECES
IVASHCHENKO, MM
ULIZKO, EP
METAL SCIENCE AND HEAT TREATMENT, 1979, 21 (9-10) : 664 - 667

← 1 2 3 4 5 →