IMPROVEMENT OF MACHINABILITY OF CONTINUOUSLY CAST LOW-CARBON FREE CUTTING STEEL .2. EFFECT OF CUTTING TOOL-CHIP INTERFACE ON BUILT-UP EDGE FORMATION

被引：0

|

作者：

KATAYAMA, S

机构：

来源：

TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN | 1985年 / 71卷 / 05期

关键词：

D O I：

暂无

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

引用

收藏

页码：S531 / S531

页数：1

相关论文

共 22 条

[1] IMPROVEMENT IN MACHINABILITY OF CONTINUOUSLY CAST LOW-CARBON FREE-CUTTING STEEL .2. EFFECT OF CUTTING TOOL-CHIP INTERFACE ON BUILT-UP EDGE FORMATION
KATAYAMA, S
IMAI, T
SUZUKI, N
TRANSACTIONS OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 25 (09) : B228 - B228
[2] IMPROVEMENT OF MACHINABILITY OF CONTINUOUSLY CAST LOW-CARBON FREE CUTTING STEEL .3. EFFECT OF MNS ON MACHINABILITY
IMAI, T
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 71 (05): : S532 - S532
[3] IMPROVEMENT OF MACHINABILITY OF CONTINUOUSLY CAST LOW-CARBON FREE CUTTING STEEL .4. EFFECT OF MNS DUCTILITY ON MACHINABILITY
YANASE, M
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 71 : 1453 - 1453
[4] IMPROVEMENT IN MACHINABILITY OF CONTINUOUSLY CAST LOW-CARBON FREE-CUTTING STEEL .3. EFFECT OF MNS ON MACHINABILITY
KATAYAMA, S
IMAI, T
KOYASU, Y
OHTANI, S
TRANSACTIONS OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 25 (09) : B229 - B229
[5] IMPROVEMENT OF MACHINABILITY OF CONTINUOUSLY CAST LOW-CARBON FREE CUTTING STEEL .1. DEVELOPMENT OF MACHINABILITY EVALUATION METHOD
KATAYAMA, S
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 71 (05): : S530 - S530
[6] IMPROVEMENT OF MACHINABILITY OF CONTINUOUSLY CAST LOW-CARBON FREE CUTTING STEEL .5. EFFECT OF TOOL MATERIALS ON MNS LAYER FORMING ON THE TOOL FACE
KATAYAMA, S
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1986, 72 (05): : S649 - S649
[7] IMPROVEMENT IN MACHINABILITY OF CONTINUOUSLY CAST LOW-CARBON FREE-CUTTING STEEL .1. DEVELOPMENT OF MACHINABILITY EVALUATION METHOD
KATAYAMA, S
IMAI, T
SUZUKI, N
TRANSACTIONS OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 25 (09) : B227 - B227
[8] PEELING OF BUILT-UP EDGE OF A CUTTING TOOL DURING MACHINING OF A FREE CUTTING STEEL AND ITS EFFECT ON TOOL LIFE
OHGO, K
WEAR, 1977, 45 (03) : 365 - 374
[9] Effect of MnS distribution on machinability in low-carbon free-cutting steel
Muroran R and D Laboratory, Nippon Steel Corp., Muroran, Hokkaido, Japan
Iron Steel Technol., 2009, 9 (45-51):
[10] SIMULATION ANALYSIS OF BUILT-UP EDGE FORMATION IN MACHINING OF LOW-CARBON STEEL
USUI, E
MAEKAWA, K
SHIRAKASHI, T
BULLETIN OF THE JAPAN SOCIETY OF PRECISION ENGINEERING, 1981, 15 (04): : 237 - 242