Modeling micro-end-milling operations. Part II: tool run-out

被引：134
|
作者：
Bao, WY [1 ]
Tansel, IN [1 ]
机构：
[1] Florida Int Univ, Dept Mech Engn, Ctr Engn & Appl Sci, Miami, FL 33174 USA
来源：
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE | 2000年 / 40卷 / 15期
关键词：
manufacture; micro-tools; end-milling; modeling;
D O I：
10.1016/S0890-6955(00)00055-9
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The effect of run-out is clearly noticed in micro-end-milling operations, while the same run-out creates negligible change at the cutting force profile of conventional end-milling operations. In this paper, the cutting force characteristics of micro-end-milling operations with tool run-out are investigated. An analytical cutting force model is developed for micro-end-milling operations with tool run-out. The proposed model has a compact set of expressions to be able to estimate the cutting force characteristics very quickly compared to the numerical approaches. The cutting forces of micro-end-milling operations simulated by the proposed model had good agreement with the experimental data. (C) 2000 Elsevier Science Ltd. All rights reserved.
引用
收藏
页码：2175 / 2192
页数：18
相关论文
共 50 条
  • [1] Modeling micro-end-milling operations. Part III: influence of tool wear
    Bao, WY
    Tansel, IN
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2000, 40 (15): : 2193 - 2211
  • [2] Modeling micro-end-milling operations. Part I: analytical cutting force model
    Bao, WY
    Tansel, IN
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2000, 40 (15): : 2155 - 2173
  • [3] Mechanistic modeling of micro milling including tool run-out
    Karpat, Yigit
    Kanli, Muammer
    Oliaei, Samad Nadimi Bavil
    JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2018, 33 (02): : 739 - 748
  • [4] Tool Run-Out Measurement in Micro Milling
    Attanasio, Aldo
    MICROMACHINES, 2017, 8 (07):
  • [5] A Novel Method for Calibration of Tool Run-out in Micro End-milling
    Zhou, Yudong
    Tian, Yanling
    Wang, Fujun
    Jing, Xiubing
    Cai, Xiang
    2017 IEEE INTERNATIONAL CONFERENCE ON MANIPULATION, MANUFACTURING AND MEASUREMENT ON THE NANOSCALE (3M-NANO), 2017, : 36 - 39
  • [6] Experimental Evaluation of Tool Run-Out in Micro Milling
    Attanasio, Aldo
    Ceretti, Elisabetta
    PROCEEDINGS OF 21ST INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING (ESAFORM 2018), 2018, 1960
  • [7] Genetic tool monitor (GTM) for micro-end-milling operations
    Tansel, IN
    Bao, WY
    Reen, NS
    Kropas-Hughes, CV
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2005, 45 (03): : 293 - 299
  • [8] Prediction of cutting forces and instantaneous tool deflection in micro end milling by considering tool run-out
    Zhang, Xuewei
    Yu, Tianbiao
    Wang, Wanshan
    INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2018, 136 : 124 - 133
  • [9] Dynamic cutting force prediction for micro end milling considering tool vibrations and run-out
    Zhang, Xuewei
    Yu, Tianbiao
    Wang, Wanshan
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2019, 233 (07) : 2248 - 2261
  • [10] Cutting forces modeling for micro flat end milling by considering tool run-out and bottom edge cutting effect
    Zhang, Xuewei
    Yu, Tianbiao
    Wang, Wanshan
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2019, 233 (02) : 470 - 485
12345