Wire Material Electrical Parameters for the Inductor Technological Complex in Production of Plastic Molding

被引：0
|
作者：
Sorokin, A. [1 ]
Filimonova, O. [1 ]
Glukhov, V [2 ]
Mirolyubova, O. [2 ]
Rodionova, U. [2 ]
机构：
[1] Samara State Tech Univ, Molodogvardeyskaya 244, Samara 443100, Russia
[2] Peter Great St Petersburg Polytech Univ, Polytech Skaya 29, St Petersburg 195251, Russia
来源：
2017 6TH INTERNATIONAL CONFERENCE ON RELIABILITY, INFOCOM TECHNOLOGIES AND OPTIMIZATION (TRENDS AND FUTURE DIRECTIONS) (ICRITO) | 2017年
基金：
俄罗斯科学基金会;
关键词：
Injection molding; extrusion; injection molding machine; polymer; inductor; power options;
D O I：
暂无
中图分类号：
TM [电工技术]; TN [电子技术、通信技术];
学科分类号：
0808 ; 0809 ;
摘要：
Defines the basic electrical parameters of the wire material of the original induction heating systems for plastics molding, which provide the required performance characteristics of the polymer. When designing induction heating systems the main parameters that determine the heating efficiency are the frequency, the level and nature of power distribution, the geometric dimensions of the inductor, is found taking into account possible technological limitations. Frequency, except in specified circumstances, determines the choice of power source and other equipment the induction heating system, i.e. determines the cost of the entire installation. In this regard, first of all, the frequency can be considered as an optimized parameter.
引用
收藏
页码：231 / 233
页数：3
相关论文
共 20 条
  • [1] Parameters of the Plastic Deformation of a Filler Wire during Electrical-Contact Welding
    M. Z. Nafikov
    I. I. Zagirov
    Kh. T. Karimov
    R. F. Masyagutov
    Russian Metallurgy (Metally), 2020, 2020 : 1491 - 1495
  • [2] Parameters of the Plastic Deformation of a Filler Wire during Electrical-Contact Welding
    Nafikov, M. Z.
    Zagirov, I. I.
    Karimov, Kh. T.
    Masyagutov, R. F.
    RUSSIAN METALLURGY, 2020, 2020 (13): : 1491 - 1495
  • [3] Effect of the boundary-layer parameters on technological properties of various oxide mixtures and semiproducts obtained by plastic molding
    Mosin, YM
    Shikhieva, GG
    REFRACTORIES AND INDUSTRIAL CERAMICS, 1999, 40 (7-8) : 341 - 346
  • [4] Effect of the boundary-layer parameters on technological properties of various oxide mixtures and semiproducts obtained by plastic molding
    Yu. M. Mosin
    G. G. Shikhieva
    Refractories and Industrial Ceramics, 1999, 40 : 341 - 346
  • [5] Effect of Charge Material and Technological Parameters on the Production of Light Metal Castings.
    Lech, Zbigniew
    Sek-Sas, Grazyna
    1976, (22):
  • [6] The influence of cut direction and process parameters in wire electrical discharge machining of carbon fibre–reinforced plastic composites
    Ramy Abdallah
    Sein Leung Soo
    Richard Hood
    The International Journal of Advanced Manufacturing Technology, 2021, 113 : 1699 - 1716
  • [7] Analysis of Effects of Cutting Parameters of Wire Electrical Discharge Machining on Material Removal Rate and Surface Integrity
    Tonday, H. R.
    Tigga, A. M.
    5TH NATIONAL CONFERENCE ON PROCESSING AND CHARACTERIZATION OF MATERIALS, 2016, 115
  • [8] SUPERSTRUCTURE OF ISO/TS 16949 FOR THE MEASUREMENT OF MATERIAL-TECHNOLOGICAL PARAMETERS OF THE PRODUCTS IN AUTOMOTIVE PRODUCTION
    Senova, Andrea
    Stofova, Lenka
    Szaryszova, Petra
    Dugas, Jaroslav
    MANAGEMENT SYSTEMS IN PRODUCTION ENGINEERING, 2021, 29 (03) : 178 - 183
  • [9] Development of New Electrical Technological Systems and Complex in the Production of Hard-to-Remove Oil Reserves
    Khlyupin, P. A.
    Khazieva, R. T.
    Vahedi, A.
    SOCAR PROCEEDINGS, 2021, : 125 - 137
  • [10] From plastic waste pyrolysis to Fuel: Impact of process parameters and material selection on hydrogen production
    Al-Fatesh, Ahmed S.
    AL-Garadi, Najib Y. A.
    Osman, Ahmed I.
    Al-Mubaddel, Fahad S.
    Ibrahim, Ahmed A.
    Khan, Wasim U.
    Alanazi, Yousef M.
    Alrashed, Maher M.
    Alothman, Othman Y.
    FUEL, 2023, 344
12