Creep behaviour of PP/glass-fibre composite adhesive lap joints

被引：2
|
作者：
Reis, PN [1 ]
Ferreira, JAM
Costa, JDM
Richardson, MOW
机构：
[1] UBI, Dept Electromech Engn, Covilha, Portugal
[2] Univ Coimbra, Dept Mech Engn, PT-3030 Coimbra, Portugal
[3] Loughborough Univ Technol, IPTME, Loughborough LE11 3TU, Leics, England
来源：
ADVANCED MATERIALS FORUM I | 2002年 / 230-2卷
关键词：
adhesive joints; composite materials; creep; environment effects;
D O I：
10.4028/www.scientific.net/KEM.230-232.315
中图分类号：
TQ174 [陶瓷工业]; TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
This paper is concerned with a creep study of composite adhesive lap joints produced from a bi-directional woven E-glass fibres and polypropylene composite. Bond preparation conditions were tested and the corresponding static strength was obtained. Creep tests were carried out within the temperature range from 20 to 50degreesC. Results of the deformation and strain rate versus time are presented. Failure time, temperature and stress were correlated using Manson-Haferd parameter. Failure mechanisms were observed by means the scanning microscopy technique.
引用
收藏
页码：315 / 318
页数：4
相关论文
共 50 条
  • [1] Creep behaviour of adhesive lap joints in thermoplastics composites
    Reis, PNB
    Ferreira, JAM
    Costa, JDM
    Richardson, MO
    JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN, 2005, 40 (03): : 287 - 294
  • [2] Fatigue behaviour of composite adhesive lap joints
    Ferreira, JAM
    Reis, PN
    Costa, JDM
    Richardson, MOW
    COMPOSITES SCIENCE AND TECHNOLOGY, 2002, 62 (10-11) : 1373 - 1379
  • [3] The behaviour of a glass-fibre epoxy composite during plate impact
    Eatwell, M.
    Millett, J. C. F.
    Bourne, N. K.
    Meziere, Y.
    SHOCK COMPRESSION OF CONDENSED MATTER - 2005, PTS 1 AND 2, 2006, 845 : 801 - 804
  • [4] Experimental investigation of pinned joints in NCF Glass-Fibre reinforced composite plates
    Inal, Oguzcan
    Atas, Akin
    JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2018, 33 (04): : 1445 - 1457
  • [5] Bolted joints in quasi-unidirectional glass-fibre NCF composite laminates
    Inal, Oguzcan
    Balikoglu, Fatih
    Atas, Akin
    COMPOSITE STRUCTURES, 2018, 183 : 536 - 544
  • [6] Creep behaviour of FM906 glass-fibre epoxy as used in heated fibre metal laminates
    Hagenbeek, Michiel
    Dias, Marcelo M.
    Sinke, Jos
    Jansen, Kaspar
    JOURNAL OF COMPOSITE MATERIALS, 2019, 53 (26-27) : 3829 - 3840
  • [7] Effect of the Surface Preparation on PP Reinforced Glass Fiber Adhesive Lap Joints Strength
    Reis, P. N. B.
    Ferreira, J. M.
    Richardson, M. O. W.
    JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS, 2012, 25 (01) : 3 - 13
  • [8] Flexural behaviour of a polymeric foam/glass-fibre composite: FE modelling and experimental testing
    Belingardi, G
    Cavatorta, MP
    Peroni, L
    HIGH PERFORMANCE STRUCTURES AND MATERIALS II, 2004, : 3 - 12
  • [9] Application of acoustic emission to study creep behaviour of composite bonded lap shear joints
    Magalhaes, AG
    de Moura, MFSF
    NDT & E INTERNATIONAL, 2005, 38 (01) : 45 - 52
  • [10] Cyclic Creep and Recovery Behaviour of Glass Fibre Reinforced Epoxy Composite
    Lovrenic-Jugovic, Martina
    Tonkovic, Zdenko
    Slokar, Ljerka
    ADVANCES IN FRACTURE AND DAMAGE MECHANICS XII, 2014, 577-578 : 657 - +
12345