Experimental Study of Microgroove Surface Using Three-Dimensional Elliptical Vibration Texturing

被引:13
|
作者
Kurniawan, Rendi [1 ]
Ali, Saood [1 ]
Park, Ki Moon [1 ]
Jung, Sang Tae [2 ]
Ko, Tae Jo [1 ]
机构
[1] Yeungnam Univ, Precis Machining Lab, Dept Mech Engn, Room 214, Gyongsan 38541, South Korea
[2] Pohang Univ Sci & Technol, Pohang Accelerator Lab, Pohang Si 37673, South Korea
来源
基金
新加坡国家研究基金会;
关键词
microgroove; vibration mark; 3D-EVT; microstructured surface; DIMPLE FORMATION; PERFORMANCE; GENERATION; TOPOGRAPHY; ALLOY;
D O I
10.1115/1.4043957
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
This paper presents our preliminary study of the microstructured surface on microgrooves patterns, which have manufactured using the three-dimensional elliptical vibration texturing (3D-EVT) method. The 3D-EVT method uses a three-dimensional trajectory of elliptical locus of the cutting tool tip in high vibration frequency to fabricate the microstructure or the vibration mark pattern on the machined surface. The experimental study has been done with a variation of the nominal cutting speeds from 300 to 600 mm/min. The preliminary results showed that in the low nominal cutting speed of 300 and 450 mm/min, the microstructured surfaces were not manufactured well due to the bulging existence on the microstructured surface in which it is correlated with the build-up edge phenomena. On the other hand, a relative excellent microstructured surface can be achieved at the higher nominal cutting speed of 600 mm/min. In addition, a lubricant could be used to obtain an excellent microstructured surface to avoid the built-up edge phenomena.
引用
收藏
页数:7
相关论文
共 50 条
  • [1] Surface topography analysis in three-dimensional elliptical vibration texturing (3D-EVT)
    Rendi Kurniawan
    Tae Jo Ko
    The International Journal of Advanced Manufacturing Technology, 2019, 102 : 1601 - 1621
  • [2] Surface topography analysis in three-dimensional elliptical vibration texturing (3D-EVT)
    Kurniawan, Rendi
    Ko, Tae Jo
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2019, 102 (5-8): : 1601 - 1621
  • [3] Three-dimensional study of microchannel with elliptical rib
    Raj, Deepak Kumar
    Datta, Aparesh
    PHYSICS OF FLUIDS, 2024, 36 (07)
  • [4] Development of a two-frequency, elliptical-vibration texturing device for surface texturing
    Kurniawan, Rendi
    Ko, Tae Jo
    Ping, Li Chang
    Kumaran, S. Thirumalai
    Kiswanto, Gandjar
    Guo, Ping
    Ehmann, Kornel F.
    JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2017, 31 (07) : 3465 - 3473
  • [5] Development of a two-frequency, elliptical-vibration texturing device for surface texturing
    Rendi Kurniawan
    Tae Jo Ko
    Li Chang Ping
    S. Thirumalai Kumaran
    Gandjar Kiswanto
    Ping Guo
    Kornel F. Ehmann
    Journal of Mechanical Science and Technology, 2017, 31 : 3465 - 3473
  • [6] An analysis of the surface generation mechanics of the elliptical vibration texturing process
    Guo, Ping
    Ehmann, Kornel F.
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2013, 64 : 85 - 95
  • [7] Three-dimensional elliptical vibration cutting device based on the curved beam
    Lin, Sheng
    Deng, Xubiao
    2019 3RD INTERNATIONAL WORKSHOP ON RENEWABLE ENERGY AND DEVELOPMENT (IWRED 2019), 2019, 267
  • [8] Experimental study on the packing of cubic particles under three-dimensional vibration
    Xie, Zhouzun
    An, Xizhong
    Wu, Yongli
    Wang, Lin
    Qian, Quan
    Yang, Xiaohong
    POWDER TECHNOLOGY, 2017, 317 : 13 - 22
  • [9] Experimental study on the packing of uniform spheres under three-dimensional vibration
    Li, C. X.
    An, X. Z.
    Yang, R. Y.
    Zou, R. P.
    Yu, A. B.
    POWDER TECHNOLOGY, 2011, 208 (03) : 617 - 622
  • [10] Heterogeneous, Three-Dimensional Texturing of Graphene
    Wang, Michael Cai
    Chun, SungGyu
    Han, Ryan Steven
    Ashraf, Ali
    Kang, Pilgyu
    Nam, SungWoo
    NANO LETTERS, 2015, 15 (03) : 1829 - 1835