Microstructure and mechanical properties of Al-12Si produced by selective laser melting

被引：13

作者：

Fefelov, A. S. ^{[1
]}

Merkushev, A. G. ^{[1
]}

Chikova, O. A. ^{[1
]}

机构：

[1] Ural Fed Univ, FSAEI, HE, 19 Mira St, Ekaterinburg 620002, Russia

来源：

INNOVATIONS AND PROSPECTS OF DEVELOPMENT OF MINING MACHINERY AND ELECTRICAL ENGINEERING | 2017年 / 87卷

关键词：

SINTERING/MELTING SLS/SLM; AL; ALLOY; STRENGTH;

D O I：

10.1088/1755-1315/87/9/092011

中图分类号：

TM [电工技术]; TN [电子技术、通信技术];

学科分类号：

0808 ; 0809 ;

摘要：

Al-12Si specimens are produced by selective laser melting (SLM) from gas atomized powders. Installation for the production of powder is original. All specimens were prepared using the EOSINT M 280 device. A fine cellular structure is observed with residual free Si along the cellular boundaries. Room temperature tensile tests reveal remarkable mechanical behavior: the samples show yield and tensile strengths of about 102 MPa and 425 MPa, respectively, along with fracture strain of 12%. The study of crack surface morphology was shown by the example of a sample. Except the spherical pores, the interface of the molten pool also appears on the fracture surface, which indicates a mixture of fragile and ductile fracture. Additionally, the agglomerated silicon group appears also on the fracture surface.

引用

页数：5

共 50 条

[1] Microstructure and mechanical properties of Al-12Si produced by selective laser melting: Effect of heat treatment
Prashanth, K. G.
Scudino, S.
Klauss, H. J.
Surreddi, K. B.
Loeber, L.
Wang, Z.
Chaubey, A. K.
Kuehn, U.
Eckert, J.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 590 : 153 - 160
[2] Tribological and corrosion properties of Al-12Si produced by selective laser melting
Prashanth, K. G.
Debalina, B.
Wang, Z.
Gostin, P. F.
Gebert, A.
Calin, M.
Kuehn, U.
Kamaraj, M.
Scudino, S.
Eckert, J.
JOURNAL OF MATERIALS RESEARCH, 2014, 29 (17) : 2044 - 2054
[3] Defining the tensile properties of Al-12Si parts produced by selective laser melting
Prashanth, K. G.
Scudino, S.
Eckert, J.
ACTA MATERIALIA, 2017, 126 : 25 - 35
[4] Friction welding of Al-12Si parts produced by selective laser melting
Prashanth, K. G.
Damodaram, R.
Scudino, S.
Wang, Z.
Rao, K. Prasad
Eckert, J.
MATERIALS & DESIGN, 2014, 57 : 632 - 637
[5] Microstructure and mechanical properties of Al-12Si and Al-3.5Cu-1.5Mg-1Si bimetal fabricated by selective laser melting
Wang, P.
Lao, C. S.
Chen, Z. W.
Liu, Y. K.
Wang, H.
Wendrock, H.
Eckert, J.
Scudino, S.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2020, 36 : 18 - 26
[6] Microstructure and mechanical properties of Al-12Si and Al-3.5Cu-1.5Mg-1Si bimetal fabricated by selective laser melting
P.Wang
C.S.Lao
Z.W.Chen
Y.K.Liu
H.Wang
H.Wendrock
J.Eckert
S.Scudino
JournalofMaterialsScience&Technology, 2020, 36 (01) : 18 - 26
[7] Influence of substrate plate heating on the fabrication of Al-12Si produced by selective laser melting
L. X. Xi
P. Ma
Y. D. Jia
A. K. Chaubey
Z. Wang
K. G. Prashanth
Transactions of the Indian National Academy of Engineering, 2021, 6 (4) : 1027 - 1036
[8] Microstructure and Mechanical Properties of Al-Si-Mg-Zr Alloy Produced by Selective Laser Melting
Lv Hongwei
Zhang Zhijie
Luo Jinjie
Geng Yaoxiang
Ju Hongbo
Yu Lihua
Xu Junhua
RARE METAL MATERIALS AND ENGINEERING, 2023, 52 (03) : 1087 - 1093
[9] Comparative investigation of microstructure, mechanical properties and strengthening mechanisms of Al-12Si/TiB2 fabricated by selective laser melting and hot pressing
Xi, L. X.
Zhang, H.
Wang, P.
Li, H. C.
Prashanth, K. G.
Lin, K. J.
Kaban, I.
Gu, D. D.
CERAMICS INTERNATIONAL, 2018, 44 (15) : 17635 - 17642
[10] A study of the microstructure and the mechanical properties of an Al-Si-Ni alloy produced via selective laser melting
Aversa, Alberta
Lorusso, Massimo
Cattano, Giulio
Manfredi, Diego
Calignano, Flaviana
Ambrosio, Elisa P.
Biamino, Sara
Fino, Paolo
Lombardi, Mariangela
Pavese, Matteo
JOURNAL OF ALLOYS AND COMPOUNDS, 2017, 695 : 1470 - 1478

← 1 2 3 4 5 →