Influence of Cutting Speed on Flank Temperature during Face Milling of Magnesium Alloy

被引：34
|
作者：
Hou, Junzhan [1 ,2 ]
Zhao, Ning [2 ]
Zhu, Shaoli [1 ]
机构：
[1] Nanyang Technol Univ, Sch Mech & Aerosp Engn, Singapore 639798, Singapore
[2] Northwestern Polytech Univ, Sch Mech Engn, Xian, Shannxi Provinc, Peoples R China
来源：
MATERIALS AND MANUFACTURING PROCESSES | 2011年 / 26卷 / 08期
关键词：
AM50A magnesium alloy; Cutting speed; Face milling; Mean flank temperature;
D O I：
10.1080/10426914.2010.536927
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Chip ignition is one of the important problems in cutting magnesium alloy due to cutting temperature rise, which is mainly caused by the increase of cutting speed. In this article, we measured the mean flank temperature through mounting two K-type thermocouples in workpiece of AM50A magnesium alloy. Effect of cutting speed on the temperature rise of tool flank was analyzed. The results show that the temperature first increases and then decreases as the cutting speed increases. The chip ignition appears when the mean flank temperature rise is about 3 degrees C in cutting magnesium alloy at ambient temperature. However, the ignition cannot be observed with further increase in temperature. The results can reasonably be used to predict and avoid the occurrence of chip ignition.
引用
收藏
页码：1059 / 1063
页数：5
相关论文
共 50 条
  • [1] Temperature on flank face of cutting tool in high speed milling
    Ueda, T
    Hosokawa, A
    Oda, K
    Yamada, K
    CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2001, 50 (01) : 37 - 40
  • [2] Mean flank temperature measurement in high speed dry cutting of magnesium alloy
    Fang, FZ
    Lee, LC
    Liu, XD
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2005, 167 (01) : 119 - 123
  • [3] Analysis of cutting forces and surface quality during face milling of a magnesium alloy
    Chirita, B.
    Grigoras, C.
    Tampu, C.
    Herghelegiu, E.
    MODERN TECHNOLOGIES IN INDUSTRIAL ENGINEERING VII (MODTECH2019), 2019, 591
  • [4] Influence of the cutting parameters on the workpiece temperature during face milling
    Nowakowski, Lukasz
    Skrzyniarz, Michal
    Miko, Edward
    Takosoglu, Jakub
    Blasiak, Slawomir
    Laski, Pawel
    Bracha, Gabriel
    Pietrala, Dawid
    Zwierzchowski, Jaroslaw
    Blasiak, Malgorzata
    EXPERIMENTAL FLUID MECHANICS 2016 (EFM16 ), 2017, 143
  • [5] Influence of cutting speed on cutting force, flank temperature, and tool wear in end milling of Ti-6Al-4V alloy
    Hou, Junzhan
    Zhou, Wei
    Duan, Hongjian
    Yang, Guang
    Xu, Hongwei
    Zhao, Ning
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2014, 70 (9-12): : 1835 - 1845
  • [6] Influence of cutting speed on cutting force, flank temperature, and tool wear in end milling of Ti-6Al-4V alloy
    Junzhan Hou
    Wei Zhou
    Hongjian Duan
    Guang Yang
    Hongwei Xu
    Ning Zhao
    The International Journal of Advanced Manufacturing Technology, 2014, 70 : 1835 - 1845
  • [7] Influence of cutting speed on cutting force, flank temperature, and tool wear in end milling of Ti-6Al-4V alloy
    Hou, J. (PG29146111@e.ntu.edu.sg), 1835, Springer London (70): : 9 - 12
  • [8] Cutting temperature in high speed milling of a near alpha titanium alloy
    Geng, G. S.
    Xu, J. H.
    Fu, Y. C.
    Ge, Y. F.
    Su, C.
    ADVANCES IN MACHINING & MANUFACTURING TECHNOLOGY VIII, 2006, 315-316 : 145 - 149
  • [9] Influence of tool nose radius and cutting performance during face milling of magnesium alloy for output responses by taguchi based grey relation analysis
    Kumaran D.
    Sivam S.P.S.S.
    Natarajan H.
    Ratna P.R.S.S.
    International Journal of Vehicle Structures and Systems, 2021, 13 (02) : 145 - 150
  • [10] Influence of the Cutting Strategy on the Temperature and Surface Flatness of the Workpiece in Face Milling
    Nowakowski, Lukasz
    Skrzyniarz, Michal
    Blasiak, Slawomir
    Bartoszuk, Marian
    MATERIALS, 2020, 13 (20) : 1 - 16
12345