Investigating the CO2 laser cutting parameters of MDF wood composite material

被引：100

作者：

Eltawahni, H. A. ^{[1
]}

Olabi, A. G. ^{[1
]}

Benyounis, K. Y. ^{[1
]}

机构：

[1] Dublin City Univ, Sch Mech & Manu Eng, Mat Proc Res Ctr, Dublin 9, Ireland

来源：

OPTICS AND LASER TECHNOLOGY | 2011年 / 43卷 / 03期

关键词：

CO2 laser cutting; Design of experiment; MDF; LASER; OPTIMIZATION;

D O I：

10.1016/j.optlastec.2010.09.006

中图分类号：

O43 [光学];

学科分类号：

070207 ; 0803 ;

摘要：

Laser cutting of medium density fibreboard (MDF) is a complicated process and the selection of the process parameters combinations is essential to get the highest quality cut section This paper presents a means for selecting the process parameters for laser cutting of MDF based on the design of experiments (DOE) approach A CO2 laser was used to cut three thicknesses 4 6 and 9 mm of MDF panels The process factors Investigated are laser power cutting speed air pressure and focal point position In this work cutting quality was evaluated by measuring the upper kerf width the lower kerf width the ratio between the upper kerf width to the lower kerf width the cut section roughness and the operating cost The effect of each factor on the quality measures was determined The optimal cutting combinations were presented in favours of high quality process output and in favours of low cutting cost (C) 2010 Elsevier Ltd All rights reserved

引用

页码：648 / 659

页数：12

共 50 条

[1] Optimization of Parameters for the Cutting of Wood-Based Materials by a CO2 Laser
Kubovsky, Ivan
Kristak, Lubos
Suja, Juraj
Gajtanska, Milada
Igaz, Rastislav
Ruziak, Ivan
Reh, Roman
APPLIED SCIENCES-BASEL, 2020, 10 (22): : 1 - 16
[2] CO2 laser cutting of MDF 2.: Estimation of power distribution
Ng, SL
Lum, KCP
Black, I
OPTICS AND LASER TECHNOLOGY, 2000, 32 (01): : 77 - 87
[3] Experimental investigation into CO2 laser cutting parameters
Yilbas, BS
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1996, 58 (2-3) : 323 - 330
[4] Study of parameters for CO2 laser cutting process
Yilbas, BS
MATERIALS AND MANUFACTURING PROCESSES, 1998, 13 (04) : 517 - 536
[5] CO2 laser cutting of MDF 1.: Determination of process parameter settings
Lum, KCP
Ng, SL
Black, I
OPTICS AND LASER TECHNOLOGY, 2000, 32 (01): : 67 - 76
[6] Impact of technological parameters of CO2 laser cutting on oxide adhesion forces on the base material
Zrak A.
Tofil S.
Šutka J.
Moravec J.
Manufacturing Technology, 2019, 19 (06): : 1094 - 1098
[7] CO2 laser beam cutting of steels:: Material issues
Manohar, M
JOURNAL OF LASER APPLICATIONS, 2006, 18 (02) : 101 - 112
[8] Optimization of Tensile Strength in the Paper Material Cutting Process Based on CO2 Laser Process Parameters
Pincjer, Ivan
Miketic, Nada
Gvoic, Vesna
Maricic, Katarina
Vukelic, Djordje
Prica, Miljana
MATERIALS, 2023, 16 (07)
[9] CO2 Laser Cutting of Glass Fiber Reinforce Polymer Composite
Fatimah, S.
Ishak, M.
Aqida, S. N.
1ST INTERNATIONAL CONFERENCE ON MECHANICAL ENGINEERING RESEARCH 2011 (ICMER2011), 2012, 36
[10] Optimisation Of Cutting Parameters Of Composite Material Laser Cutting Process By Taguchi Method
Lokesh, S.
Niresh, J.
Neelakrishnan, S.
Rahul, S. P. Deepak
2017 5TH INTERNATIONAL CONFERENCE ON MECHANICAL ENGINEERING, MATERIALS SCIENCE AND CIVIL ENGINEERING, 2018, 324

← 1 2 3 4 5 →