DETERMINATION OF LOCAL DISTRIBUTION OF HARDNESS FOR INVESTIGATION OF MATERIAL BEHAVIOR UNDER LOAD APPROACHING ITS STRENGTH

被引：0
|
作者：
Valach, Jaroslav [1 ]
Zdarsky, Marek [2 ]
Kytyr, Daniel [1 ]
Doktor, Tomas [1 ]
Sperl, Martin [1 ]
机构：
[1] Acad Sci Czech Republ, Vvi, Inst Theoret & Appl Mech, Prague 19000 9, Czech Republic
[2] Czech Tech Univ, Fac Transportat Sci, Prague 11000 1, Czech Republic
来源：
CHEMICKE LISTY | 2012年 / 106卷
关键词：
hardness mapping; crack propagation; image analysis; thermography;
D O I：
暂无
中图分类号：
O6 [化学];
学科分类号：
0703 ;
摘要：
J. Valach(a), M. Zd'arsky(b), D. Kytyr(a), T. Doktor(a), and M. Sperl(a) ((a)Institute of Theoretical and Applied Mechanics, Academy of Sciences of the Czech Republic, v.v.i., Prague, (b)Czech Technical University in Prague, Faculty of Transportation Sciences, Prague, Czech Republic): Determination of Local Distribution of Hardness for Investigation of Material Behavior Under Load Approaching its Strength The paper presents enhanced method for study of severe plastic deformation by hardness mapping utilizing portable hardness tester, flatbed scanner and software processing tool. This technique can be advantageous in situations, where crude information is not only sufficient, but also preferred, especially when it concerns testing on-site and on medium to large scale specimens and construction. Validity of the approach is supported by a comparison of hardness mapping results to the results obtained by an independent method based on evaluation of plastic strains from thermograms. It is shown that both methods determined similar shape and the extent of the plastic zone of the studied specimens.
引用
收藏
页码：S551 / S554
页数：4
相关论文
共 50 条
  • [1] Investigation of creep behaviour under load during indentation experiments and its influence on hardness and modulus results
    Chudoba, T
    Richter, F
    SURFACE & COATINGS TECHNOLOGY, 2001, 148 (2-3): : 191 - 198
  • [2] INVESTIGATION OF THE STRENGTH AND PLASTICITY OF METALS UNDER IMPACT LOAD
    KOZLOV, GM
    INDUSTRIAL LABORATORY, 1960, 26 (11): : 1470 - 1474
  • [3] Strength distribution of planar local load-sharing bundles
    Habeeb, C. N. Irfan
    Mahesh, Sivasambu
    PHYSICAL REVIEW E, 2015, 92 (02)
  • [4] Influence of the material properties of a tub on its top load strength
    van Dijk, R
    Hunter, J
    Deerenberg, E
    PACKAGING TECHNOLOGY AND SCIENCE, 1999, 12 (04) : 193 - 201
  • [5] Determination of material hardness according to sizes of restored mark without load indentor recording
    Anikeev, E.F.
    Nikolaev, V.A.
    Metallurg, 1996, (05):
  • [6] A NEW PROCEDURE FOR DETERMINATION OF POINT LOAD STRENGTH IN SITE INVESTIGATION
    TURKE, N
    DEARMAN, WR
    QUARTERLY JOURNAL OF ENGINEERING GEOLOGY, 1986, 19 (03): : 321 - 321
  • [7] EFFECT OF LOAD DISTRIBUTION AND MATERIAL PROPERTIES ON THE STRENGTH OF DRICKAMER ANVILS.
    Gerasimovich, A.V.
    Soviet Journal of Superhard Materials (English translation of Sverkhtverdye Materialy), 1984, 6 (05): : 23 - 27
  • [8] EFFECT OF A NONUNIFORM STRESS DISTRIBUTION ON STRENGTH UNDER CYCLIC LOAD
    BONDAL, GV
    INDUSTRIAL LABORATORY, 1967, 33 (09): : 1345 - &
  • [9] INVESTIGATION OF BEHAVIOR OF POLYMER MATERIALS UNDER A PROLONGED LOAD
    RAKHIMOV, RZ
    VOSKRESE.VA
    INDUSTRIAL LABORATORY, 1966, 32 (12): : 1849 - &
  • [10] CALCULATION OF THE STRENGTH OF BRITTLE ENVELOPES UNDER LOCAL STATIC LOAD.
    Abramyan, E.A.
    Senyushchenkov, M.A.
    Glass and Ceramics (English translation of Steklo i Keramika), 1986, 43 (7-8): : 303 - 305
12345