Effect of Traverse Speed on Microstructure and Microhardness of Cu/B4C Surface Composite Produced by Friction Stir Processing

被引：12

作者：

Sathiskumar, R. ^{[1
]}

Murugan, N. ^{[1
]}

Dinaharan, I. ^{[2
]}

Vijay, S. J. ^{[2
]}

机构：

[1] Coimbatore Inst Technol, Dept Mech Engn, Coimbatore 641014, Tamil Nadu, India

[2] Karunya Univ, Sch Mech Sci, CRM, Coimbatore 641114, Tamil Nadu, India

来源：

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS | 2013年 / 66卷 / 04期

关键词：

Friction stir processing; Surface composite; Microstructure; Microhardness; PARTICLE-REINFORCED COMPOSITE; METAL-MATRIX COMPOSITES; MECHANICAL-PROPERTIES; FABRICATION;

D O I：

10.1007/s12666-013-0259-5

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

Friction stir processing (FSP) has evolved as a potential candidate to fabricate surface composites. This paper investigates the influence of traverse speed on microstructure and microhardness of Cu/B4C surface composite fabricated using FSP. The traverse speed was varied from 20 to 60 in steps of 20 mm/min. The tool rotational speed, axial force and groove width were kept constant. Optical microscopy and scanning electron microscopy were employed to study the microstructure of the fabricated surface composites. The results indicated that the traverse speed significantly influenced the area of the surface composite and distribution of B4C particles. The area of the surface composite was found to bear an inversely proportional relationship to traverse speed. Lower traverse speed exhibited homogenous distribution of B4C particles while higher traverse speed caused poor distribution of B4C particles in the surface composite.

引用

页码：333 / 337

页数：5

共 50 条

[1] Effect of Traverse Speed on Microstructure and Microhardness of Cu/B4C Surface Composite Produced by Friction Stir Processing
R. Sathiskumar
N. Murugan
I. Dinaharan
S. J. Vijay
Transactions of the Indian Institute of Metals, 2013, 66 : 333 - 337
[2] Influence of tool rotational speed on microstructure and sliding wear behavior of Cu/B4C surface composite synthesized by friction stir processing
Sathiskumar, R.
Dinaharan, I.
Murugan, N.
Vijay, S. J.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2015, 25 (01) : 95 - 102
[3] Microstructure, microhardness and wear properties investigation in friction stir processing of stir cast Mg/B4C metal matrix composite
Singh, Amandeep
Singh, Palwinder
Singh, Amardeep
Ram, Baljinder
Bala, Niraj
SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES, 2025, 13 (01):
[4] Metallurgy of friction stir-processed Cu/B4C surface composite
Sathiskumar, Ramasamy
Murugan, Nadarajan
Dinaharan, Issac
Vijay, Santhiyagu J.
EMERGING MATERIALS RESEARCH, 2013, 2 (01) : 27 - 31
[5] FABRICATION AND CHARACTERIZATION OF Cu/B4C SURFACE DISPERSION STRENGTHENED COMPOSITE USING FRICTION STIR PROCESSING
Sathiskumar, R.
Murugan, N.
Dinaharan, I.
Vijay, S. J.
ARCHIVES OF METALLURGY AND MATERIALS, 2014, 59 (01) : 83 - 87
[6] Effect on Microstructure and Performance of B4C Content in B4C/Cu Composite
Shu, Dayu
Li, Xiuqing
Yang, Qingxia
METALS, 2021, 11 (08)
[7] Microstructural and Wear Investigations of the Mg/B4C Surface Composite Prepared Through Friction Stir Processing
Joshi, Sumit
Yuvaraj, N.
Singh, Ramesh Chandra
Chaudhary, Rajiv
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2020, 73 (12) : 3007 - 3018
[8] Microstructural and Wear Investigations of the Mg/B4C Surface Composite Prepared Through Friction Stir Processing
Sumit Joshi
N. Yuvaraj
Ramesh Chandra Singh
Rajiv Chaudhary
Transactions of the Indian Institute of Metals, 2020, 73 : 3007 - 3018
[9] Characterization of Cu/SiC surface composite produced by friction stir processing
Iwaszko, J.
Kudla, K.
BULLETIN OF THE POLISH ACADEMY OF SCIENCES-TECHNICAL SCIENCES, 2020, 68 (03) : 555 - 564
[10] Effect of friction stir processing with B4C particles on the microstructure and mechanical properties of 6061 aluminum alloy
Zhao, Yong
Huang, Xiaolu
Li, Qiming
Huang, Jian
Yan, Keng
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2015, 78 (9-12): : 1437 - 1443

← 1 2 3 4 5 →