Effect of cooling methods on dimensional accuracy and surface finish of a turned titanium part

被引：27
|
作者：
Islam, M. N. [1 ]
Anggono, J. M. [2 ]
Pramanik, A. [1 ]
Boswell, B. [1 ]
机构：
[1] Curtin Univ, Dept Mech Engn, Bentley, WA 6102, Australia
[2] CV Duta Teknik, Tangerang, Indonesia
来源：
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY | 2013年 / 69卷 / 9-12期
关键词：
Dry turning; Flood turning; Cryogenic cooling turning; Titanium alloy; Pareto ANOVA; Taguchi method; TOOL WEAR; CUTTING PARAMETERS; MINIMUM QUANTITY; LUBRICATION MQL; TAGUCHI METHOD; ROUGHNESS; PERFORMANCE; CHIP; OPTIMIZATION; MECHANISMS;
D O I：
10.1007/s00170-013-5223-3
中图分类号：
TP [自动化技术、计算机技术];
学科分类号：
0812 ;
摘要：
In metal cutting, the choice of cooling method influences the deformation mechanism, which is related to the dimensional accuracy and surface finish of the parts. The deformation mechanism of titanium alloys under machining conditions is known to be very different from that of commonly used industrial materials. Therefore, the effect of cooling methods on dimensional accuracy and surface finish in machining titanium is of particular interest. This paper investigates experimentally and analytically the influence of cooling method and cutting parameters on two major dimensional accuracy characteristics of a turned titanium part-diameter error and circularity, and surface finish. Data were analyzed via three methods: traditional analysis, Pareto ANOVA, and Taguchi method. The findings indicate that the cooling method has significant effect on circularity error (contribution ratio 76.75 %), moderate effect on diameter error (contribution ratio 25.00 %), and negligible effect on surface finish (contribution ratio 0.16 %).
引用
收藏
页码：2711 / 2722
页数：12
相关论文
共 50 条
  • [1] Effect of cooling methods on dimensional accuracy and surface finish of a turned titanium part
    M. N. Islam
    J. M. Anggono
    A. Pramanik
    B. Boswell
    The International Journal of Advanced Manufacturing Technology, 2013, 69 : 2711 - 2722
  • [2] Effect of cooling methods on dimensional accuracy and surface finish in reaming
    Islam M.N.
    Boswell B.
    International Journal of Machining and Machinability of Materials, 2019, 21 (03) : 187 - 213
  • [3] EFFECT OF ADDITIONAL FACTORS ON DIMENSIONAL ACCURACY AND SURFACE FINISH OF TURNED PARTS
    Islam, M. N.
    MACHINING SCIENCE AND TECHNOLOGY, 2013, 17 (01) : 145 - 162
  • [4] Comparison of dry and flood turning in terms of dimensional accuracy and surface finish of turned parts
    Rafai N.H.
    Islam M.N.
    Lecture Notes in Electrical Engineering, 2011, 90 LNEE : 501 - 513
  • [5] Effect of Amount of Cutting Fluid on Surface Finish of Turned Parts
    Islam, M. N.
    APPLIED MECHANICS AND MANUFACTURING TECHNOLOGY, 2011, 87 : 170 - 177
  • [6] Effect of surface slope and build orientation on surface finish and dimensional accuracy in material jetting processes
    Khoshkhoo, Ali
    Carrano, Andres L.
    Blersch, David M.
    46TH SME NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE, NAMRC 46, 2018, 26 : 720 - 730
  • [7] Effect of Cutting Fluid Supply Strategies on Surface Finish of Turned Parts
    Islam, M. N.
    Rafai, N. H.
    Heng, B. C.
    MANUFACTURING SCIENCE AND TECHNOLOGY, PTS 1-8, 2012, 383-390 : 4576 - 4584
  • [8] EFFECT OF THERMAL DEFORMATIONS ON DIMENSIONAL ACCURACY OF TURNED WORKPIECES
    CHOWANIE.W
    JEDRZEJE.J
    MECHANIK MIESIECZNIK NAUKOWO-TECHNICZNY, 1974, 47 (02): : 70 - 75
  • [9] AN INVESTIGATION INTO DIMENSIONAL ACCURACY AND SURFACE FINISH ACHIEVABLE IN DRY TURNING
    Rafai, N. H.
    Islam, M. N.
    MACHINING SCIENCE AND TECHNOLOGY, 2009, 13 (04) : 571 - 589
  • [10] The effect of methods for hardening finish treatment of blades made of titanium alloys on the state of their surface layer
    V. A. Boguslaev
    G. V. Pukhal’skaya
    A. D. Koval’
    L. P. Stepanova
    V. V. Tkachenko
    Metal Science and Heat Treatment, 2008, 50 : 18 - 24
12345