THERMODYNAMIC ANALYSIS OF 6XXX SERIES AL ALLOYS: PHASE FRACTION DIAGRAMS

被引：8
|
作者：
Cui, S. [1 ]
Mishra, R. [2 ]
Jung, I. -H. [1 ]
机构：
[1] McGill Univ, Dept Min & Mat Engn, Montreal, PQ, Canada
[2] Gen Motors R&D Ctr, Warren, MI USA
来源：
JOURNAL OF MINING AND METALLURGY SECTION B-METALLURGY | 2018年 / 54卷 / 01期
基金：
加拿大自然科学与工程研究理事会;
关键词：
Aluminum alloy; Thermodynamic calculation; Solidification; Alloy design; C TERNARY-SYSTEM; SI ALLOYS; MECHANICAL-PROPERTIES; BINARY-SYSTEMS; MG SYSTEMS; MN; MICROSTRUCTURE; ASSESSMENTS;
D O I：
10.2298/JMMB170512052C
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
Microstructural evolution of 6xxx Al alloys during various metallurgical processes was analyzed using accurate thermodynamic database. Phase fractions of all the possible precipitate phases which can form in the as-cast and equilibrium states of the Al-Mg-Si-Cu-Fe-Mn-Cr alloys were calculated over the technically useful composition range. The influence of minor elements such as Cu, Fe, Mn, and Cr on the amount of each type of precipitate in the as-cast and equilibrium conditions were analyzed. Phase fraction diagrams at 500 degrees C were mapped in the composition range of 0-1.1 wt.% Mg and 0-0.7 wt.% Si to investigate the as-homogenized microstructure. In addition, phase fraction diagram of Mg2Si at 177 degrees C was mapped to understand the microstructure after final annealing of 6xxx Al alloy. Based on the calculated diagrams, the design strategy of 6xxx Al alloy to produce highest strength due to Mg2Si is discussed.
引用
收藏
页码：119 / 131
页数：13
相关论文
共 50 条
  • [1] Non-equilibrium reactions in 6xxx series Al alloys
    Hsu, C
    O'Reilly, KAQ
    Cantor, B
    Hamerton, R
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2001, 304 (1-2): : 119 - 124
  • [2] The localized corrosion of Al 6XXX alloys
    Shaw, BA
    McCosby, MM
    Abdullah, AM
    Pickering, HW
    JOM-JOURNAL OF THE MINERALS METALS & MATERIALS SOCIETY, 2001, 53 (07): : 42 - 46
  • [3] The localized corrosion of Al 6XXX alloys
    B. A. Shaw
    M. M. McCosby
    A. M. Abdullah
    H. W. Pickering
    JOM, 2001, 53 : 42 - 46
  • [4] Continuous cooling transformation diagrams for 6XXX aluminium alloys
    Bryantsev, P. Yu
    5TH INTERNATIONAL EEIGM/AMASE/FORGEMAT CONFERENCE ON ADVANCED MATERIALS RESEARCH, 2009, 5
  • [5] Surface Modification of 6xxx Series Aluminum Alloys
    Bhat, Kuruveri Udaya
    Panemangalore, Devadas Bhat
    Kuruveri, Spandana Bhat
    John, Merbin
    Menezes, Pradeep L.
    COATINGS, 2022, 12 (02)
  • [6] Dispersoid Phases in 6xxx Series Aluminium Alloys
    Strobel, Katherina
    Sweet, Elizabeth
    Easton, Mark
    Nie, Jian-Feng
    Couper, Malcolm
    PRICM 7, PTS 1-3, 2010, 654-656 : 926 - +
  • [7] HOT DEFORMATION OF 6XXX SERIES ALUMINIUM ALLOYS
    Mrowka-Nowotnik, G.
    Sieniawski, J.
    Kotowski, S.
    Nowotnik, A.
    Motyka, M.
    ARCHIVES OF METALLURGY AND MATERIALS, 2015, 60 (02) : 1079 - 1084
  • [8] Phase fraction mapping in the as-cast microstructure of extrudable 6xxx aluminum alloys
    Sarafoglou, Panagiota I.
    Haidemenopoulos, Gregory N.
    INTERNATIONAL JOURNAL OF MATERIALS RESEARCH, 2014, 105 (12) : 1202 - 1209
  • [9] Design of New 6xxx Series Al Alloy Using the Calphad Thermodynamic Database
    Cui, Senlin
    Mishra, Raj
    Jung, In-Ho
    LIGHT METALS 2017, 2017, : 159 - 165
  • [10] Quasi-peritectic solidification reactions in 6xxx series wrought Al alloys
    Sha, G
    O'Reilly, KAQ
    Cantor, B
    Titchmarsh, JM
    Hamerton, RG
    ACTA MATERIALIA, 2003, 51 (07) : 1883 - 1897
12345