Transition process of pump device model test in closed test-bed

被引：0

作者：

Ma X. ^{[1
]}

Li H. ^{[1
]}

Shi W. ^{[1
]}

Shao X. ^{[1
]}

机构：

[1] Research Center of Fluid Machinery Engineering and Technology, Jiangsu University, Zhenjiang

来源：

Paiguan Jixie Gongcheng Xuebao/Journal of Drainage and Irrigation Machinery Engineering | 2011年 / 29卷 / 05期

关键词：

Closed test-bed; Inlet and outlet pressure; Pump device model; Shaft power; Transition process;

D O I：

10.3969/j.issn.1674-8530.2011.05.005

中图分类号：

学科分类号：

摘要：

In order to study the characteristics of the pump test-bed and pump working conditions, physical simulation experiment method was used to do the experiment of a model pump used in some pump station on a vertical closed pump test-bed. The averaged pressure before the inlet and after the outlet of the pump, as well as the averaged pressure in upstream and downstream of the pump test-bed, and pump working conditions parameters were collected with gradually reducing the flow under constant rotating speed. The change characters of pump pressure before the inlet and after the outlet as well as shaft power were analyzed, and the internal changes of both the pump device model and test system during the transition to be stable were discussed. The test results show that during the transition process, the inlet pressure fluctuation of the pump is subtle and can always be in relatively stable state. The outlet pressure in the initial stage shows ascendant trend fluctuations, and the fluctuations are intensive. But after a while, tends are relatively stable. The shaft power changes are similar to the pressure fluctuations after outlet. In the initial stage, changes are obvious, but the fluctuations gradually become stable. This period of the process has continued for more than 90 s.

引用

页码：392 / 396

页数：4

共 10 条

[1] Benra F.K., Numerical and experimental investigation on the flow induced oscillations of a single-blade pump impeller, Fluids Engineering, 6, 128, pp. 783-793, (2006)
[2] Kelder J.D.H., Dijkers R.J.H., Esch B.P.M., Et al., Experimental and theoretical study of the flow in the volute of a low specific speed pump, Fluid Dynamics Research, 28, 4, pp. 267-280, (2001)
[3] Yao Z., Wang F., Xiao R., Et al., Key issues in pressure fluctuation experiments for centrifugal pumps, Journal of Drainage and Irrigation Machinery Engineering, 28, 3, pp. 219-223, (2010)
[4] Zheng Y., Liu J., Zhou D., Et al., Pressure pulsation of model test in large size axial flow pump, Journal of Drainage and Irrigation Machinery Engineering, 28, 1, pp. 51-55, (2010)
[5] Wang F., Zhang L., Zhang Z., Analysis on pressure fluctuation of unsteady flow in axial-flow pump, Journal of Hydraulic Engineering, 38, 8, pp. 1003-1008, (2007)
[6] Ni Y., Pan Z., Li H., Et al., Application of characters of discharge pressure fluctuation to monitor of centrifugal pump, Drainage and Irrigation Machinery, 24, 5, pp. 40-43, (2006)
[7] Ji L., Li H., Wang Y., Et al., Measures of reducing pressure pulsation in centrifugal pulp pump, Fluid Machinery, 34, 8, pp. 50-52, (2006)
[8] Yuan S., Xue F., Yuan J., Et al., Experimental study on impact of pressure fluctuation on flow noise in centrifugal pump, Drainage and Irrigation Machinery, 27, 5, pp. 287-290, (2009)
[9] Cong G., Wang F., Numerical investigation of unsteady pressure fluctuations near volute tongue in a double-suction centrifugal pump, Transactions of the Chinese Society for Agricultural Machinery, 39, 6, pp. 60-67, (2008)
[10] Liu H., Ren Y., Tan M., Et al., CFD calculation and test of pressure fluctuation in double-channel pump, Journal of Drainage and Irrigation Machinery Engineering, 28, 4, pp. 277-281, (2010)

← 1 →