Ultrasonic guided wave-based evaluation for mechanical properties of interlaminar toughening carbon fiber/epoxy composites with microcapsules

被引：0
|
作者：
Wang B. [1 ,2 ]
Yu X. [1 ,2 ]
Zhao G. [1 ,2 ]
Luo Y. [1 ,2 ]
Hao W. [1 ,2 ]
机构：
[1] National Center for International Research on Structural Health management of Critical Components, Jiangsu University, Zhenjiang
[2] Institute of Structural Health Monitoring, Faculty of Civil Engineering and Mechanics, Jiangsu University, Zhenjiang
来源：
Fuhe Cailiao Xuebao/Acta Materiae Compositae Sinica | 2021年 / 38卷 / 03期
关键词：
Agglomerate microcapsules; Carbon fiber (CF); Composites; Epoxy (EP); Interlaminar toughening; Mechanical properties evaluation; Ultrasonic guided wave;
D O I：
10.13801/j.cnki.fhclxb.20200619.002
中图分类号：
学科分类号：
摘要：
The interlaminar-toughening T300 carbon fiber/epoxy (CF/EP) composites with agglomerate microcapsules were prepared using hot-compaction laminating technology. The toughening effect was evaluated through mode Ⅰ interlaminar fracture tests conducted on double cantilever beam (DCB) CF/EP composites. The interlaminar properties of virgin and toughened CF/EP composites were evaluated by ultrasonic guided wave technology. The microstructures of interlaminar fracture surfaces of CF/EP composites were observed by SEM to reveal the toughening mechanism of microcapsules and explain the ultrasonic guided wave detection results. The results indicate that the microcapsules are distributed in the interlamination matrix resin in the form of agglomeration, which effectively improve the interlaminar fracture toughness of CF/EP composites. The filling of microcapsules changes the characteristics of the interlaminar matrix of the CF/EP composites, which increases attenuation of the propagating guided waves and causes the response signal peak to decrease. Meanwhile, the agglomerate microcapsules change the vibration response of the CF/EP composites to the excitation of the five-peak wave with a center frequency of 125 kHz, resulting in the amplitude of the center frequency in the signal spectrum being lower than that of the virgin CF/EP composites. Copyright ©2021 Acta Materiae Compositae Sinica. All rights reserved.
引用
收藏
页码：788 / 796
页数：8
相关论文
共 26 条
  • [1] DU S Y., Advanced composite materials and aerospace engineering, Acta Materiae Compositae Sinica, 24, 1, pp. 1-12, (2007)
  • [2] DONG H M, YI X S, AN X F, Et al., Development of interleaved fibre-reinforced thermoset polymer matrix composites, Acta Materiae Compositae Sinica, 31, 2, pp. 273-285, (2014)
  • [3] HAO W F, GE D Y, MA Y J, Et al., Experimental investigation on deformation and strength of carbon/epoxy laminated curved beams, Polymer Testing, 31, 4, pp. 520-526, (2012)
  • [4] STEVANOVIC D., Delamination properties of a vinyl-ester/glass fibre composite toughened by particulate-modified interlayers, (2001)
  • [5] ALJARRAH M T, ABDELAL N R., Improvement of the mode Ⅰ interlaminar fracture toughness of carbon fiber composite reinforced with electrospun nylon nanofiber, Composites Part B: Engineering, 165, pp. 379-385, (2019)
  • [6] GUO Z Z, XU W, YU Y., A simple method for determining mode Ⅰ interlaminar fracture toughness of composite at low temperature, Acta Materiae Compositae Sinica, 36, 5, pp. 154-159, (2019)
  • [7] GAO Y, LIU L, WU Z J, Et al., Toughening and self-healing fiber-reinforced polymer composites using carbon nanotube modified poly(ethylene-co-methacrylic acid) sandwich membrane, Composites Part A: Applied Science and Manufacturing, 124, (2019)
  • [8] GAO F, JIAO G Q, NING R C, Et al., Damage resistance of the composite laminates with interlayer thermoplastic particles, Acta Materiae Compositae Sinica, 22, 2, pp. 116-120, (2005)
  • [9] MO Z C, HU C Y, HUO J C, Et al., Interlayer-toughening carbon fiber/epoxy composites with short ramie fiber, Acta Materiae Compositae Sinica, 34, 6, pp. 1237-1244, (2017)
  • [10] OU Y, GONZALEZ C, JOSE V J., Interlaminar toughening in structural carbon fiber/epoxy composites interleaved with carbon nanotube veils, Composites Part A: Applied Science and Manufacturing, 124, (2019)
123