The possibility of friction stir welding of high nitrogen-containing austenitic stainless steel

被引：0
|
作者：
Miyano Y. [1 ]
Fujii H. [2 ]
Sun Y. [2 ]
Ieko K. [3 ]
Katada Y. [4 ]
Kamiya O. [3 ]
机构：
[1] Faculty of Educational Systems and Studies, Akita University, Akita-city, AKITA, 1-1, Tegatagakuen-Machi
[2] Joining and Welding Research Institute, Osaka University, Suita, Osaka 565-0871
[3] Faulty of Engineering and Resource Science, Akita University, Akita-city, AKITA, 1-1, Tegatagakuen-Machi
[4] National Institute for Materials Science, Tsukuba-city Ibaraki 305-0047
来源：
International Journal of the Society of Material Engineering for Resources | 2010年 / 17卷 / 02期
关键词：
α; formation; Austenite; Butt-welding; Electro-slag remelting methods; Friction stir welding;
D O I：
10.5188/ijsmer.17.197
中图分类号：
学科分类号：
摘要：
To develop the practical use of high nitrogen-containing austenitic stainless steels (HNS), the possibility of using friction stir welding (FSW) of HNS was examined. In this report, butt-welding of 2 mm thick HNS steel plates was performed using a load-controlled FSW machine. Two types of welding tool materials were used in this study, namely, a Si3N4-based material and a WC-Co-based material. For FSW with Si3N4, fullpenetrated and defect-free butt welding joints were successfully produced. On the other hand, for FSW with WC-Co, the tool was deformed and the stir zone did not completely reach the bottom. The stir zone produced by the Si3N4 tool showed a Vicker's hardness higher than the base metal and displayed a fine microstructure due to recrystallization. The yield strength and the tensile strength of the welds produced by the Si3N4 tool exceeded that of the base metal. © 2010 Soc. Mater. Eng. Resour.
引用
收藏
页码：197 / 200
页数：3
相关论文
共 50 条
  • [1] Mechanical properties of friction stir butt welds of high nitrogen-containing austenitic stainless steel
    Miyano, Yasuyuki
    Fujii, Hidetoshi
    Sun, Yufeng
    Katada, Yasuyuki
    Kuroda, Shuji
    Kamiya, Osamu
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (06): : 2917 - 2921
  • [2] Mechanical properties of friction stir welded high nitrogen containing austenitic stainless steel
    Miyano, Y.
    Fujii, H.
    Sun, Y. F.
    Katada, Y.
    Kuroda, S.
    Kudo, G.
    Kamiya, O.
    PROCEEDINGS OF THE 1ST INTERNATIONAL JOINT SYMPOSIUM ON JOINING AND WELDING, 2013, : 95 - 100
  • [3] Friction stir welding of AISI 304 austenitic stainless steel
    Meran, C.
    Kovan, V.
    Alptekin, A.
    MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, 2007, 38 (10) : 829 - 835
  • [4] High Speed-High Quality Friction Stir Welding of Austenitic Stainless Steel
    Ishikawa, Takeshi
    Fujii, Hidetoshi
    Genchi, Kazuo
    Iwaki, Shunichi
    Matsuoka, Shigeki
    Nogi, Kiyoshi
    ISIJ INTERNATIONAL, 2009, 49 (06) : 897 - 901
  • [5] Friction stir welding of single crystal austenitic stainless steel
    Ikeda, K.
    Jeon, J. J. S.
    Mironov, S.
    Sato, Y. S.
    Fujii, H. T.
    Kokawa, H.
    Park, S. H. C.
    Hirano, S.
    PROCEEDINGS OF THE 1ST INTERNATIONAL JOINT SYMPOSIUM ON JOINING AND WELDING, 2013, : 449 - 451
  • [6] High Quality-High Speed Friction Stir Welding of 304 Austenitic Stainless Steel
    Ishikawa, Takeshi
    Fujii, Hidetoshi
    Genchi, Kazuo
    Iwaki, Shunichi
    Matsuoka, Shigeki
    Nogi, Kiyoshi
    TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2008, 94 (11): : 539 - 544
  • [7] QUENCHING DEFECTS IN A NITROGEN-CONTAINING AUSTENITIC STAINLESS-STEEL
    KIKUCHI, M
    TANAKA, T
    TANAKA, R
    METALLURGICAL TRANSACTIONS, 1974, 5 (06): : 1520 - 1521
  • [8] Laser beam welding of high-nitrogen-containing austenitic stainless steel
    Iamboliev, T
    Zumbilev, A
    Kalev, L
    Christov, S
    Ianev, V
    Stang, RG
    WELDING JOURNAL, 1999, 78 (07) : 245S - 252S
  • [9] Friction stir spot welding of single-crystal austenitic stainless steel
    Jeon, J.
    Mironov, S.
    Sato, Y. S.
    Kokawa, H.
    Park, S. H. C.
    Hirano, S.
    ACTA MATERIALIA, 2011, 59 (20) : 7439 - 7449
  • [10] Microstructural evolution of 304 austenitic stainless steel during friction stir welding
    Kokawa, H
    Park, SHC
    Sato, YS
    Okamoto, K
    Hirano, S
    Inagaki, M
    PROCEEDINGS OF THE FOURTEENTH (2004) INTERNATIONAL OFFSHORE AND POLAR ENGINEERING CONFERENCE, VOL 4, 2004, : 73 - 77
12345