Research status and prospect of shot peening for carburized gear roots

被引：0
|
作者：
Zhu P.-F. [1 ,2 ]
Yan H.-Z. [1 ]
Chen Z. [1 ]
Wu S.-X. [1 ]
Zhang H. [1 ]
机构：
[1] Central South University, Changsha
[2] Kaifeng University, Kaifeng
来源：
Surface Technology | 2021年 / 50卷 / 01期
基金：
中国国家自然科学基金;
关键词：
Bending fatigue; Crack; Gear root; Shot peening; Surface integrity;
D O I：
10.16490/j.cnki.issn.1001-3660.2021.01.002
中图分类号：
学科分类号：
摘要：
Bending fatigue is the main failure form of gear transmission, which seriously affects the service performance of gears. Shot peening strengthening technology is a common surface strengthening method for gears that can effectively improve the bending fatigue resistance for gear roots. Two typical shot peening strengthening methods (air-blast peening and centrifugal peening) were introduced, which were compared from the aspects of application range, machining efficiency, spraying principle, surface integrity, etc., respectively. To reveal the mechanism of shot peening strengthening, numerical simulation and parameter optimization methods of shot peening were summarized, influence mechanism of shot peening on the surface integrity of gear roots was analyzed, and correlation of surface integrity parameters was expounded. Meanwhile, the fatigue fracture mechanism (including crack initiation and propagation) of shot-peened gears were revealed. On this basis, influence factors of bending fatigue for shot-peened gears were emphatically discussed, and measures to improve the fatigue strength of gears were put forward. In addition, the gain in fatigue strength of shot-peened gear was discussed briefly, and bending fatigue modeling methods for shot-peened gears were generalized. Finally, shot-peening strengthening process of gear roots was summarized and its development trend was prospected. © 2021, Chongqing Wujiu Periodicals Press. All rights reserved.
引用
收藏
页码：10 / 27
页数：17
相关论文
共 109 条
  • [1] Zhu P.-F., Yan H.-Z., Chen Z., Et al., Research status and prospect of shot peening of gear tooth flanks[J], Surface Technology, 49, 4, pp. 113-131, (2020)
  • [2] Shot Peening Applications [M], (2019)
  • [3] Lawerenz M., Shot peening and its effect on gea-ring[R], Milwaukee: SAE 841090, (1984)
  • [4] Lambert R., Aylott D., Shaw J.A., Evaluation of bending fatigue strength in automotive gear steel subjected to shot peening techniques[J], Procedia Structural Integrity, 13, pp. 1855-1860, (2018)
  • [5] Eckersley J., Gearing up for higher loads[J], The Shot Peener, 7, 3, pp. 1-11, (1993)
  • [6] Matsumura S., Hamasaka N., High strength and compactness of gears by WHSP (Double hard shot pee-ning) technology[J], Komatsu Technical Report, 52, 158, pp. 1-5, (2006)
  • [7] Straub J., Special Performance of Transmission Parts by Shot Peening[R], (1973)
  • [8] Burrell N.K., Controlled shot peening of automotive components[J], SAE Transactions, 10, pp. 44-51, (1985)
  • [9] Lawerenz M., Ekis I., Creating an in-house shot peening specification for gears[J], The Shot Peener, 6, 4, pp. 13-18, (1992)
  • [10] Matsui K., Eto H., Yukitake K., Et al., Increase in fatigue limit of gears by compound surface refining using vacuum carburizing, contour induction hardening and double shot peening[J], JSME International Journal Series a Solid Mechanics and Material Engineering, 45, 2, pp. 290-297, (2002)
12345678910