Permanent magnets with embedded phase changing material for electric motor thermal management

被引:1
|
作者
Lamarre, Jean-Michel [1 ]
Ibrahim, Maged [2 ]
Pelletier, Roger [1 ]
Vatandoost, Hossein [1 ]
Bernier, Fabrice [1 ]
机构
[1] Automot Res Ctr, Natl Res Council Canada, Boucherville, PQ J4B6Y4, Canada
[2] German Int Univ Cairo, Adm Capital, Reg Ring Rd, Cairo Governorate Desert, Cairo, Egypt
关键词
IMPROVEMENT; ERYTHRITOL; MACHINES; POWER;
D O I
10.1063/5.0219982
中图分类号
O59 [应用物理学];
学科分类号
摘要
The magnetic performance of NdFeB permanent magnets rapidly decreases as their operation temperature increases. This limits the power output of electric motors as their internal temperature quickly increases with the power demand. This is particularly problematic for applications where high peak power is required for a short period of time, for example during automobile highway acceleration or during an airplane lift-off. With the advances in additive manufacturing, one can envision to fabricate more complex motor geometries and magnetic structures, without additional costs, allowing for enhanced functionalities such as better thermal management. In this context, this paper investigates the feasibility of using phase changing materials (PCMs) to mitigate the temperature rise in permanent magnets (PMs) fabricated by additive manufacturing. The potential of PCM and its relevance was validated by modeling the thermal response of an electric motor during a representative electric vehicle driving scenario. It was found that segmented magnets with embedded phase changing materials would allow to efficiently control temperature rise. To validate the simulation results, PM test pieces with and without embedded PCMs were fabricated using cold spray additive manufacturing and tested using a custom laser thermal cycling setup.
引用
收藏
页数:8
相关论文
共 50 条
  • [1] Analysis of the Phase Control of Synchronous Electric Motor with Permanent Magnets
    Kurnosov, D. A.
    Voronin, S. G.
    2017 INTERNATIONAL CONFERENCE ON INDUSTRIAL ENGINEERING, APPLICATIONS AND MANUFACTURING (ICIEAM), 2017,
  • [2] Study of the thermal behavior of a synchronous motor with permanent magnets
    Seghir-Oualil, Souhil
    Harmand, Souad
    Laloy, Daniel
    Phillipart, Olivier
    MECANIQUE & INDUSTRIES, 2009, 10 (06): : 455 - 476
  • [3] Design of the electric motor with permanent magnets for electric vehicle according the driving cycle
    Grebenikov V.V.
    Priymak M.V.
    Grebenikov, V.V. (elm1153@gmail.com), 2018, Institute of Electrodynamics, National Academy of Sciences of Ukraine (2018): : 65 - 68
  • [4] Study on the Effect of Permanent Magnets in a Novel Pole-Changing Motor
    Ou, Lezhi
    Wang, Xuefan
    Pan, Weidong
    2016 19TH INTERNATIONAL CONFERENCE ON ELECTRICAL MACHINES AND SYSTEMS (ICEMS 2016), 2016,
  • [5] Heat Transfer and Thermal Management of Interior Permanent Magnet Synchronous Electric Motor
    Wu, Pey-Shey
    Hsieh, Min-Fu
    Cai, Wei Ling
    Liu, Jen-Hsiang
    Huang, Yun-Ting
    Caceres, Jose Fernando
    Chang, Shyy Woei
    INVENTIONS, 2019, 4 (04)
  • [6] EXPERIMENTAL RESEARCH OF THE CONTROLLER FOR CONTROL OF THE TRACTION ELECTRIC MOTOR ON PERMANENT MAGNETS
    Zharkin A.F.
    Pavlov V.B.
    Grebenikov V.V.
    Technical Electrodynamics, 2022, 2022 (05): : 52 - 58
  • [7] Material selection of permanent magnets, considering thermal properties correctly
    Trout, SR
    ELECTRICAL INSULATION CONFERENCE AND ELECTRICAL MANUFACTURING & COIL WINDING CONFERENCE, PROCEEDINGS, 2001, : 365 - 370
  • [9] Embedded Position Detection for Permanent Magnet Synchronous Motor With Built-In Magnets
    Wang, Shuxian
    Peng, Donglin
    Wu, Zhiyi
    IEEE SENSORS JOURNAL, 2019, 19 (21) : 9818 - 9825
  • [10] Analysis of flux leakage in a brushless permanent-magnet motor with embedded magnets
    Tsai, WB
    Chang, TY
    IEEE TRANSACTIONS ON MAGNETICS, 1999, 35 (01) : 543 - 547