Arc erosion behavior of TiB2/Cu composites

被引：0
|
作者：
Li G. [1 ,2 ]
Liu Y. [1 ,3 ]
Guo X. [2 ,3 ]
Feng J. [1 ,2 ]
Song K. [1 ,3 ]
Tian B. [1 ,3 ]
机构：
[1] School of Materials Science and Engineering, He'nan University of Science and Technology, Luoyang
[2] He'nan Key Laboratory of Non-Ferrous Materials Science and Processing Technology, Luoyang
[3] Collaborative Innovation Center of Nonferrous Metals, He'nan Province, Luoyang
来源：
Liu, Yong (liuyong@haust.edu.cn.) | 2018年 / Beijing University of Aeronautics and Astronautics (BUAA)卷 / 35期
关键词：
Arc duration; Arc erosion; Composites; Material transfer; Spark plasma sintering; TiB[!sub]2[!/sub]/Cu;
D O I：
10.13801/j.cnki.fhclxb.20170531.003
中图分类号：
学科分类号：
摘要：
The TiB2/Cu composites with TiB2 mass fraction of 1wt%-5wt% were prepared by spark plasma sintering (SPS), and the electrical conductivity and hardness were tested. The electrical conductivity of TiB2/Cu composites decreases from 96.9% (International Annealed Copper Standard, IACS) to 65.1%(IACS) with TiB2 mass fraction increasing from 0 to 5wt%, while the Brinell hardness increases from 42.8 to 65.2. To discuss the effect of TiB2 content and current on TiB2/Cu composites arc erosion, the electrical contact tests were performed at 24 V and different direct current for TiB2/Cu composites with the different TiB2 mass fractions. For TiB2/Cu composites with different TiB2 mass fraction, the average arc duration, average arc energy and mass loss increase with the increase of current. The cathode of TiB2/Cu composites mass loss more than that of the anode. In general, the TiB2/Cu composites are transferred from cathode to anode. At 24 V and 25 A, the arc duration and arc energy of TiB2/Cu composites with different TiB2 mass fractions are fluctuant with the increase of operation times. On the whole, it shows a tendency to increase gradually. The 3wt% TiB2/Cu composite has higher stability, the average arc duration and average arc energy are lower than the others. With the increase of mass fraction of TiB2, TiB2/Cu composites present less mass loss and shallower arc erosion pits. © 2018, Editorial Office of Acta Materiae Compositae Sinica. All right reserved.
引用
收藏
页码：616 / 622
页数：6
相关论文
共 20 条
  • [1] Si F., Wang J.B., Liu S.T., Et al., Preparation process research status and development trend of Ag-SnO<sub>2</sub> electrical contact materials, Electronic Components and Materials, 34, 9, pp. 31-34, (2015)
  • [2] Yang Z.Q., Liu Y., Tian B.H., Et al., Critical conditions of dynamic recrystallization of TiC/Cu-Al<sub>2</sub>O<sub>3</sub> composites, Acta Materiae Compositae Sinica, 31, 4, pp. 963-969, (2014)
  • [3] Guo Y.L., Li D.M., Li H.Y., Et al., Progress in Cu-based contact materials of low voltage apparatus, Electrical Engineering Materials, 3, pp. 10-13, (2011)
  • [4] Han B., Shi Q.N., Xie M., Et al., Arc erosion characteristics of W-15wt%Cu electric contact materials under DC condition, Rare Metal Materials and Engineering, 41, 6, pp. 994-997, (2012)
  • [5] Swingler J., Sumption A., Arc erosion of AgSnO<sub>2</sub> electrical contacts at different stages of a break operation, Rare Metals, 29, 3, pp. 248-254, (2010)
  • [6] Biyik S., Arslan F., Aydin M., Arc-erosion behavior of boric oxide-reinforced silver-based electrical contact materials produced by mechanical alloying, Journal of Electronic Materials, 44, 1, pp. 457-466, (2015)
  • [7] Hauner F., Jeannot D., Mcneilly K., Et al., Advanced AgSnO<sub>2</sub> contact materials for the replacement of AgCdO in high current contactors, Proceedings of the 56th IEEE Holm Conference on Electrical Contacts. Chicago: IEEE, pp. 225-230, (2000)
  • [8] Mutzel T., Niederreuther R., Development of contact material solutions for low voltage circuit breaker applications (2), Proceedings of the 57th IEEE Holm Conference on Electrical Contacts., pp. 1-6, (2011)
  • [9] Bai X.P., Lin W.H., Zhang M.J., Cotact materials for low voltage electric apparatus, Electrical Engineering Materials, 3, pp. 12-16, (2007)
  • [10] Omer G., Ertan E., The investigation of contact performance of oxide reinforced copper composite via mechanical alloying, Journal of Materials Processing Technology, 209, 3, pp. 1286-1290, (2009)
12