Lightweight design of fast steering mirror for space cameras

被引：0
|
作者：
Wang K. [1 ,2 ]
Xin H. [1 ]
Xu H. [1 ]
Ren T. [1 ,2 ]
机构：
[1] Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun
[2] University of Chinese Academy of Sciences, Beijing
来源：
Hongwai yu Jiguang Gongcheng/Infrared and Laser Engineering | 2019年 / 48卷 / 04期
关键词：
Contrastive analysis; Fast steering mirror; Finite element simulation; Lightweight; Multi-objective optimization; Rear support in center;
D O I：
10.3788/IRLA201948.0418001
中图分类号：
学科分类号：
摘要：
Aiming at the working conditions and working requirements of the fast steering mirrors for space cameras, a lightweight scheme for fast steering mirrors was proposed. Taking the mirror with a diameter of 100 mm as the research object, the lightweight structure based on ribs was designed, and the calculation method of the equivalent thickness of standard circular mirror was proposed. Two supporting methods of the mirror, rear support with three points or rear support with a central point, were designed separately, and the results of the contrastive analysis indicate that mirror supported with a central point can avoid mutual interference between multiple support points, which is caused by inconsistent temperature deformation of the holder and the mirror. The accuracy of the mirror surface is higher, and because of its simple structure, the total mass of the wobble assembly is lighter. In order to achieve the best overall performance of the fast steering mirror structure, a multi-objective optimization of the main structural parameters was executed, the total mass of the wobble assembly and the RMS value of the mirror surface were simultaneously used as the optimization goals. The optimization results showed that the rib height and the adapter thickness contributed the most to the overall performance of the structure. The total mass of the wobble assembly under the optimized scheme is only 95.75 g, and the first-order resonant frequency of the structure is 217 Hz, the RMS of the mirror surface is 7.26 nm under the condition of -8℃temperature load, which meets the design requirements while achieving a 40.4% reduction in the weight of the mirror. © 2019, Editorial Board of Journal of Infrared and Laser Engineering. All right reserved.
引用
收藏
相关论文
共 15 条
  • [1] Du Y., Liu B., Hu B., Et al., A compensation method of image motion in fullframe CCD aerial camera, Acta Photonica Sinica, 36, 12, pp. 2334-2336, (2007)
  • [2] Fu C., Jiang L., Image tracking system with a finesteeringmirror, OptoElectronic Engineering, 3, pp. 1-8, (1994)
  • [3] Loney G.C., Design of a highbandwidth steering mirror for spacebased optical communications, Active and Adaptive Optical Components, (1992)
  • [4] Xu X., Yang H., Wang B., Et al., Research on key technology of faststeering mirror, Laser & Infrared, 43, 10, pp. 1095-1103, (2013)
  • [5] Qin C., Sha W., Zhang X., Et al., Optimization of local space mirror surface shape influenced by temperature, OptoElectronic Engineering, 42, 2, pp. 28-34, (2015)
  • [6] Bao Q., Sha W., Chen C., Et al., Lightweight and optimization design of rectangular reflective mirror supported in centre, Infrared and Laser Engineering, 46, 7, (2017)
  • [7] Wang F., Analysis of influence of temperature and supporting methods on 1.2 m SiC primary mirror surface figure, Acta Photonica Sinica, 40, 6, pp. 933-936, (2011)
  • [8] Li F., Ruan P., Zhao B., Et al., Finite element analysis of the plane mirror fastened by adhesive, Optical Technique, 32, 6, pp. 896-899, (2006)
  • [9] Wang R., Tian W., Wang P., Et al., Effect of temperature change on the surface accuracy of bonded lens, Chinese Journal of Lasers, 38, 8, pp. 201-206, (2011)
  • [10] Yan Y., Jin G., Yang H., Lightweight structural design of space mirror, Infrared and Laser Engineering, 37, 1, pp. 97-101, (2008)
12