Model of rectangular section control roll bending force for electrical steel in six-high tandem cold mill

被引：0
|
作者：
Song C. [1 ,2 ,3 ]
Cao J. [1 ,2 ,3 ,4 ]
Wang L. [1 ,2 ,3 ]
Zhao Q. [1 ,2 ,3 ,4 ]
Li Y. [1 ]
Wang Y. [1 ,2 ,3 ]
机构：
[1] School of Mechanical Engineering, University of Science and Technology Beijing, Beijing
[2] Institute of Artificial Intelligence, University of Science and Technology Beijing, Beijing
[3] National Engineering Research Center of Flat Rolling Equipment(University of Science and Technology Beijing), Beijing
[4] Shunde Graduate School, University of Science and Technology Beijing, Foshan
来源：
Harbin Gongye Daxue Xuebao/Journal of Harbin Institute of Technology | 2022年 / 54卷 / 07期
关键词：
6-high tandem cold rolling mill; Bending force model; Electrical steel; Finite element model; Rectangular section; Shape control;
D O I：
10.11918/202105033
中图分类号：
学科分类号：
摘要：
To meet the quality requirements of "Dead Flat" rectangular section super flat material such as wide electrical steel sheet in the new generation of high-tech tandem cold rolling mill, an integrated simulation model of 6-high tandem cold rolling mill was established by explicit dynamic finite element method. The accuracy of the finite element model was verified by field industrial rolling test data. The influence of different rolling factors on the crown of load roll gap in complete rolling process of electrical steel is analyzed quantitatively. Based on the shape control mechanism of 6-high UCM cold rolling mill and EDW-N(Edge Drop Control Work Rolls for Non-shifting of the Work Rolls) work rolls independently designed by our research group, the bending force mathematical model of rectangular section control of electrical steel in 6-high tandem cold rolling mill was established. The parameters of the bending force mathematical model were determined by finite element simulation and field industrial rolling test data, and its accuracy was verified. The continuous test feedback data of a large 1 420 mm six-high tandem cold mill show that the high precision average C15≤7 μm ratio of electrical steel has been increased from 38.58% to 67.74%, which gives full play to the high precision shape control ability of the 6-high tandem cold rolling mill and can control the shape quality in a wide range. It provides innovative solutions and implementation paths for solving the bottleneck problem of rectangular section control of 6-high UCM cold rolling mill for non-shifting of the work rolls. Copyright ©2022 Journal of Harbin Institute of Technology.All rights reserved.
引用
收藏
页码：143 / 150
页数：7
相关论文
共 26 条
  • [1] ABDULRAHMAN A, JIANG Zhengyi, WEI Dongbin, Finite element analysis of thin strip profile in asymmetric cold rolling considering work roll crossing and shifting, Advanced Materials Research, 1061, (2015)
  • [2] ZHANG Qingdong, ZHANG Xiaofeng, WEN Jie, Theory and technology of transverse thickness deviation control for DI tinplate during tandem cold rolling, Journal of Mechanical Engineering, 49, 24, (2013)
  • [3] KLAMMA K., CVC technology in cold rolling mills, MPT Metallurgical Plant and Technology, 8, 3, (1985)
  • [4] YANG Guanghui, CAO Jianguo, ZHANG Jie, Et al., SmartCrown work roll contour of a 4-hi tandem cold rolling mill, Journal of University of Science and Technology Beijing, 28, 7, (2006)
  • [5] HANS-GEORG H, FRIEDRICH W H, RUEDIGER H, Et al., A new way to reduce the edge drop, Steel Research, 69, 4, (1998)
  • [6] WANG Junsheng, ZHAO Qilin, JIAO Zhijie, Et al., The research on the principle and application for T-WRS & C cold mill, Heavy Machinery, 6, (2001)
  • [7] SHUNJI K, SHOICHI I, RYUJI H, Et al., Edge profile control using pair cross mill in cold rolling, Iron and Steel Engineer, 73, 6, (1996)
  • [8] CAO Jianguo, JIANG Jun, QIU Lan, Et al., High precision integrated profile and flatness control for new-generation high-tech wide strip cold rolling mills, Journal of Central South University (Science and Technology), 50, 7, (2019)
  • [9] ISHI T, SUGIYAMA T., Applications of HC mill in hot steel strip rolling, Hitachi Review, 36, 2, (1987)
  • [10] KENICHI Y, KENJIROU N, KAZUO K, Et al., Shape controll ability in new 6-high mill (UC-4 Mill) with small diameter work rolls, ISIJ International, 31, 6, (1991)
123