Influence of fraction of coarse-grained heat affected zone on impact toughness for 09MnNiDR welded joint

被引：0
|
作者：
Cao R. [1 ]
Yang Z. [1 ]
Li J. [2 ]
Lei W. [2 ]
Zhang J. [3 ]
Chen J. [1 ]
机构：
[1] State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metal, Lanzhou University of Technology, Lanzhou
[2] Lanzhou Ls Testing Technology Co., Ltd., Lanzhou
[3] Lanzhou Ls Heavy Equipment Co., Ltd., Lanzhou
来源：
Hanjie Xuebao/Transactions of the China Welding Institution | 2020年 / 41卷 / 05期
关键词：
09MnNiDR steel; Coarse grain heat-affected zone; Impact toughness; The weakest region;
D O I：
10.12073/j.hjxb.20190818003
中图分类号：
学科分类号：
摘要：
The impact absorbed energy of various regions of the heat affected zone(HAZ) of submerged arc welding actual welded joint for 09MnNiDR low temperature pressure vessel steel was measured, the microstructures, fracture surface were observed and anlyzed. Based on the experimental results, the microstructures of all regions of HAZ, the weakest region can be determined, and the effects of the weakest region on impact toughness of the welded joint were further discussed. The results show that at-70℃, the average impact absorbed energy of the base metal, subcritical heat affected zone, intercritical heat affected zone, and fine grain heat affected zone of the welded joint is above 270 J, which all show good toughness. The average impact absorbed energy of the weld metal is 139 J. The coarse grain heat affected zone (CGHAZ) is the weakest region of the welded joint. When the notch tip is completely composed of CGHAZ, the impact absorbed energy of 20 J is reached. The impact energy of CGHAZ decrease to 92.7% of the base metal. The microstructure of CGHAZ is composed of coarse granular bainite, lath bainite and block ferrite. With the increase of the fraction of CGHAZ in front of the notch tip, the closer from notch location is, the lower the impact absorbed energy of the specimen is, which fully reflects the influence of the weakest region on the impact toughness. © 2020, Editorial Board of Transactions of the China Welding Institution, Magazine Agency Welding. All right reserved.
引用
收藏
页码：7 / 13
页数：6
相关论文
共 13 条
  • [1] Lan L, Qiu C, Zhao D, Et al., Analysis of microstructural variation and mechanical behaviors in submerged arc welded joint of high strength low carbon bainitic steel, Materials Science & Engineering A, 558, 12, pp. 592-601, (2012)
  • [2] Yang Y, Cheng J, Nie W J, Et al., Investigation on the microstructure and toughness of coarse grained heat affected zone in X-100 multi-phase pipeline steel with high Nb content, Materials Science & Engineering A, 558, 12, pp. 692-701, (2012)
  • [3] Cui Bing, Peng Yun, Peng Mengdu, Et al., Effect of heat input on crack growth behavior of CGHAZ of Q890 high-performance steel, Transactions of the China Welding Institution, 38, 8, pp. 63-67, (2017)
  • [4] Zhou Y, Jia T, Zhang X, Et al., Microstructure and toughness of the CGHAZ of an offshore platform steel, Journal of Materials Processing Technology, 219, 5, pp. 314-320, (2015)
  • [5] Zhu Z, Han J, Li H, Influence of heat input on microstructure and toughness properties in simulated CGHAZ of X80 steel manufactured using high-temperature processing, Metallurgical and Materials Transactions A, 46, 11, pp. 5467-5475, (2015)
  • [6] Qin Hua, Su Yunhai, Lian Jingbao, Microstructure and properties in heat affected zone of BWELDY960Q steel by welding thermal simulation test, Transactions of the China Welding Institution, 39, 11, pp. 97-101, (2018)
  • [7] Jang J, Ju J, Lee B, Et al., Effects of microstructural change on fracture characteristics in coarse-grained heat-affected zones of QLT-processes 9% Ni steel, Materials Science & Engineering A, 340, 1-2, pp. 68-79, (2003)
  • [8] Yang S, Ju L, Cong W, On the heterogeneous microstructure development in the welded joint of 12MnNiVR pressure vessel steel subjected to high heat input electrogas welding, Journal of Materials Science & Technology, 35, 8, pp. 1747-1752, (2019)
  • [9] Cao R, Yang Z, Chan Z, Et al., The determination of the weakest zone and the effects of the weakest zone on the impact toughness of the 12Cr2Mo1R welded joint, Journal of Manufacturing Processes, 50, 2, pp. 539-546, (2020)
  • [10] Chen J, Cao R., Micromechanism of cleavage fracture of metals, (2014)
12