Microstructure and properties of copper / steel TIG welded joint based on high-entropy alloy interlayer

被引：0
|
作者：
Jiang S. [1 ]
Zhang J. [1 ]
Zhao M. [1 ]
机构：
[1] College of Materials Science and Engineering, China University of Petroleum (East China), Qingdao
来源：
Zhongguo Shiyou Daxue Xuebao (Ziran Kexue Ban)/Journal of China University of Petroleum (Edition of Natural Science) | 2023年 / 47卷 / 06期
关键词：
high-entropy alloy interlayer; microstructure; properties; Q235; steel; T2; copper; TIG welding;
D O I：
10.3969/j.issn.1673-5005.2023.06.018
中图分类号：
学科分类号：
摘要：
The copper/ steel composite structure can not only meet the performance requirements of different environments, but also can reduce the consumption of copper materials and greatly reduce the cost of components. However, the physical and chemical properties of copper and steel are quite different, and the extremely poor miscibility will lead to liquid phase separation or defects after welding. Based on the idea of solid solution-high entropy of weld metal, Fe5Co30Cr30Ni30Cu5 high-entropy alloy was designed as the intermediate layer to carry out TIG welding of T2 copper and Q235 steel, and the microstructure and properties of the intermediate layer and welded joint were analyzed. The results show that, Fe5Co30Cr30Ni30Cu5 high-entropy alloy is a single-phase FCC solid solution with good strength and plastic toughness. Using the high-entropy alloy as the intermediate layer material, the reliable connection between T2 copper and Q235 steel can be achieved by the TIG welding method. The welded joint is formed well, without pores, cracks and other defects. The weld microstructure is a simple solid solution with FCC structure, which has a remarkable high entropy characteristic. The average tensile strength value of the welded joint is 225 MPa, reaching 91% of the strength of T2 copper, and the extension ratio after fracture can reach 44%. The fracture of joint occurs in the heat-affected zone on the copper side. There are a large number of dimples on the fracture surface, showing the significant characteristic of ductile fracture. © 2023 University of Petroleum, China. All rights reserved.
引用
收藏
页码：154 / 161
页数：7
相关论文
共 23 条
  • [1] PATRA S, ARORA K S, SHOME M, Et al., Interface characteristics and performance of magnetic pulse welded copper-steel tubes [J], Journal of Materials Processing Technology, 245, 1, pp. 278-286, (2017)
  • [2] ZHANG H, JIAO K X, ZHANG J L, Et al., Experimental and numerical investigations of interface characteristics of copper/ steel composite prepared by explosive welding [J], Materials & Design, 154, 3, pp. 140-152, (2018)
  • [3] WANG Y X, LI X J, WANG X, Et al., Fabrication of a thick copper-stainless steel clad plate for nuclear fusion equipment by explosive welding [J], Fusion Engineering and Design, 137, pp. 91-96, (2018)
  • [4] LU Shixiong, SONG Jianling, YANG Shiqin, Et al., Content of Fe in TIG cladding copper alloy layer on surface of steel, Transactions of the China Welding Institution, 29, 8, pp. 85-88, (2008)
  • [5] CHENG Z, HUANG J, YE Z, Et al., Microstructures and mechanical properties of copper-stainless steel butt-welded joints by MIG-TIG double-sided arc welding [J], Journal of Materials Processing Technology, 265, 8, pp. 87-98, (2018)
  • [6] FU Jun, Research on laser welding of copper and steel dissimilar materials, (2009)
  • [7] SHIRI S G, NAZARZADEH M, SHARIFITABAR M, Et al., Gas tungsten arc welding of CP-copper to 304 stainless steel using different filler materials, Transactions of Nonferrous Metals Society of China, 22, 12, pp. 2937-2942, (2012)
  • [8] MAGNABOSCO I, FERRO P, BONOLLO F, Et al., An investigation of fusion zone microstructures in electron beam welding of copper-stainless steel [J], Materials Science and Engineering A, 424, 1, pp. 163-173, (2006)
  • [9] XING Li, LI Lei, KE Liming, Microstructure analysis of friction stir welding joint between low carbon steel and red copper, Transactions of the China Welding Institution, 28, 2, pp. 17-20, (2007)
  • [10] CHEN Xiangping, TANG Jie, WEI Guoqiang, Et al., Study on microstructure and properties of flame brazed steel/ copper joint [J], Hot Working Technology of China, 21, pp. 235-237, (2017)
123