Mechanical Properties of Polyurea Material under Quasi-static and Dynamic Loading

被引：0
|
作者：
Jia Z. [1 ]
Wang S. [1 ]
Chen Y. [2 ]
Wang Z. [3 ]
Cui H. [1 ]
Zhang P. [3 ]
Xu Y. [4 ,5 ,6 ]
机构：
[1] Science and Technology on Transient Impact Laboratory, Beijing
[2] Unit 32381 of PLA, Beijing
[3] School of Mechatronics Engineering, North University of China, Taiyuan
[4] State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing
[5] Chongqing Innovation Center, Beijing Institute of Technology, Chongqing
[6] Key Laboratory of High Energy Density Materials of Ministry of Education, Beijing Institute of Technology, Beijing
来源：
Binggong Xuebao/Acta Armamentarii | 2021年 / 42卷
关键词：
Dynamic load; Fracture energy; Mechanical property; Polyurea; Quasi-static; Tangent modulus; Yield strength;
D O I：
10.3969/j.issn.1000-1093.2021.S1.019
中图分类号：
学科分类号：
摘要：
The changing law of mechanical properties of polyurea material under quasi-static and dynamic loading are studied.The polyurea material was stretched and compressed to obtain the stress-strain curve of the material by using an universal material testing machine and Hopkinson bar, and then the impack test of Hopkinson bar was conducted. The results show that the tangent modulus of polyurea material increases approximately exponentially with the increase in strain rate under quasi-static loading, and decreases approximately linearly under dynamic loading. As the strain rate increases, the strength (tensile strength and yield strength) and fracture energy of polyurea material gradually increase.It is concluded that the polyurea material has a significant strain rate effect, and the "decreasing hardening" characteristics of polyurea material under high strain rate loading are closely related to the anti-knock and impact resistance properties of polyurea. From low strain rate to high strain rate loading, the polyurea material transitions from a rubbery state to a glassy state, and its strength is significantly enhanced. © 2021, Editorial Board of Acta Armamentarii. All right reserved.
引用
收藏
页码：151 / 158
页数：7
相关论文
共 16 条
  • [1] HUANG Y Y., Study on mechanism of anti-fragment penetration of polyurea coated composite structure, (2018)
  • [2] SUN J, CHEN J J, LU M, Et al., Application of polyurea on U.S. Navy ships, Modern Paint Finishing, 12, 3, pp. 57-60, (2009)
  • [3] GAN Y D, SONG L, YANG L M., Numerical simulation for anti-blast performances of steel plate coated with elastomer, Acta Armamentarii, 30, pp. 15-18, (2009)
  • [4] AMINI M R, SIMON J, NEMAT-NASSER S., Numerical modeling of effect of polyurea on response of steel plates to impulse loads in direct pressure-pulse experiments, Mechanics of Materials, 42, 6, pp. 615-627, (2010)
  • [5] AHSAN S, ALIEZA V A, AMIRKHIZI A V, Et al., Numerical study of the effect of polyurea on the performance of steel plates under blast loads, Mechanics of Materials, 64, (2013)
  • [6] ADRIAN R, BUCUR F, GABRIELA T, Et al., Experimental study on polyurea coating effects on deformation of metallic plates subjected to air blast loads[J], Materiale Plastice, 53, 4, pp. 670-674, (2016)
  • [7] WANG J G, REN H Q, WU X Y, Et al., Blast response of polymer-retrofitted masonry unit walls, Composites Part B: Engineering, 128, pp. 174-181, (2017)
  • [8] RAMAN S N, NGO T, LU J, Et al., Experimental investigation on the tensile behavior of polyurea at high strain rates, Materials & Design, 50, pp. 124-129, (2013)
  • [9] XIAO Y C., Study of dynamic mechanical property and impact da-mage behavior of PBX, (2016)
  • [10] WANG J B, GAO G F, DU Z H, Et al., Dynamic state performance and constitutive relation of polycarbonate for bullet cores, Journal of Vibration and Shock, 38, 5, pp. 7-12, (2019)
12