Modeling and performance analysis of a combined thermal Brownian heat pump cycle

被引：0
|
作者：
Qi C. [3 ]
Ding Z. [3 ]
Chen L. [1 ,2 ]
Ge Y. [1 ,2 ]
Feng H. [1 ,2 ]
机构：
[1] Institute of Thermal Science and Power Engineering, Wuhan Institute of Technology, Wuhan
[2] School of Mechanical & Electrical Engineering, Wuhan Institute of Technology, Wuhan
[3] College of Power Engineering, Naval University of Engineering, Wuhan
来源：
Zhongguo Kexue Jishu Kexue/Scientia Sinica Technologica | 2021年 / 51卷 / 12期
关键词：
Combined thermal Brownian heat pump cycle; COP; Finite time thermodynamics; Heating load; Thermal Brownian heat pump cycle;
D O I：
10.1360/SST-2020-0417
中图分类号：
学科分类号：
摘要：
Based on finite-time thermodynamics theory, this paper proposes a two-stage thermal Brownian heat pump cycle model combined with an intermediate reservoir. The model is formed by two Brownian heat pump cycles operating in series. Two heat pump cycles operate between three heat reservoirs with constant temperature. In this regard, finite-rate heat transfer processes exist among heat pump cycles and reservoirs. In consideration of the heat transfer losses among reservoirs and heat pump cycles, the expressions of heating load and coefficient of performance (COP) are derived. The influence of design parameters on system performance is analyzed by numerical calculations. Results show that heating load decreases monotonically with the increase in the barrier height of the potential and increases monotonically with the increase in the external load and the asymmetry of the potential. The COP reaches the maximum values with the barrier height of the potential, the asymmetry of the potential, and the external load. When the heat reservoir temperatures are constant, the closer the intermediate heat reservoir temperature is to the topping cycle heat reservoir temperature, the higher the heating load and the COP. Compared with one-stage thermal Brownian heat pump cycle, which works between the heat source and sink with the same temperatures, the combined Brownian heat pump cycle has a larger heating load but a reduced COP. © 2021, Science Press. All right reserved.
引用
收藏
页码：1519 / 1529
页数：10
相关论文
共 63 条
  • [1] Zhang X, Ai B, Transport of overdamped Brownian particles driven by ac forces and time-delayed feedback, J Phys A-Math Theor, 43, (2010)
  • [2] Asfaw M, Thermodynamic feature of a Brownian heat engine operating between two heat baths, Phys Rev E, 89, (2014)
  • [3] Schmitt R K, Parrondo J M R, Linke H, Et al., Molecular motor efficiency is maximized in the presence of both power-stroke and rectification through feedback, New J Phys, 17, (2015)
  • [4] Long R, Li B, Liu W, Performance analysis for Feynman's ratchet as a refrigerator with heat leak under different figure of merits, Appl Math Model, 40, pp. 10437-10446, (2016)
  • [5] Acikkalp E, Analysis of a Brownian heat engine with ecological criteria, Eur Phys J Plus, 131, (2016)
  • [6] Chen L G., Finite-Time Thermodynamic Analysis of Irreversible Processes and Cycles, (2005)
  • [7] Lin G X, Chen J C., Investigation on the optimum performance and parametric design of a variety of energy conversion systems, J Xiamen Univ (Nat Sci), 50, pp. 227-238, (2011)
  • [8] Chen L G, Progress in optimization of mass transfer processes based on mass entransy dissipation extremum principle, Sci China Tech Sci, 57, pp. 2305-2327, (2014)
  • [9] Yang Z M, Liao T J, Lin B H, Performance optimization of a solid oxide fuel cell-stirling heat engine hybrid power system (in Chinese), Sci Sin Tech, 44, pp. 822-832, (2014)
  • [10] Lin J, Huang Z F, Lin B H, Et al., Parametric optimum design of an irreversible photon-enhanced thermionic emission solar cell hybrid system (in Chinese), Sci Sin Tech, 46, pp. 225-234, (2016)
1234567