Cutting Performance of Polished and Coated Twist Drill for Machining Austenitic Stainless Steel

被引：0
|
作者：
Luo S. [1 ,2 ]
Yuan B. [1 ,2 ]
Bian L.-L. [1 ,2 ]
Zeng T. [1 ,2 ]
Tang A.-M. [1 ,2 ]
Yang Z.-P. [1 ,2 ]
Pei F. [1 ,2 ]
机构：
[1] Zhuzhou Cemented Carbide Cutting Tools Co., Ltd., Hunan, Zhuzhou
[2] State Key Laboratory of Cemented Carbide, Hunan, Zhuzhou
来源：
Surface Technology | 2022年 / 51卷 / 04期
关键词：
austenitic stainless steel (1Cr18Ni9Ti); polished and coated carbide twist drill; tool durability; tool wear mechanism; tool wear morphology;
D O I：
10.16490/j.cnki.issn.1001-3660.2022.04.030
中图分类号：
学科分类号：
摘要：
This work aims to improve the cutting efficiency of coated twist drill for machining austenitic stainless steel. According to different process routes of polishing before coated and polishing before and after coated, the advanced polishing technology of tool substrate and coating was adopted to prepare carbide twist drill. Then, two kinds of the polished and coated twist drills and the coated twist drill which untreated by polishing process were selected to drill austenitic stainless steel, and the influence of the polishing technology before and after coated on the durability, wear morphology and wear mechanism of coated carbide twist drill were analyzed. After the initial surface of the coated carbide twist drill was polished, the average surface roughness of the flute rake face decreased from 10.77 μm to 5.09 μm, and the reduction range reached 52.7%, and the surface quality of the coating was significantly improved. When given the same cutting condition, the durability of twist drill was polished before and after coated and twist drill was polished before coated was 150% and 106.1% higher than that of unpolished twist drill respectively, and the durability of twist drill was polished before and after coated was 21.3% higher than that of twist drill was polished before coated. The failure causes of unpolished coated twist drill were crater wear, tip chipping and chip adhesion. The failure causes of twist drill was polished before coated were crater wear, notch wear around the cutting edge and coating peeling off. The failure causes of twist drill was polished before and after coated were micro chipping, coating peeling off and chip adhesion, and the damage degree of it was the least of all. The polishing technology of tool substrate and coating surface of the common coated twist drill has remarkable advantages in reducing the damage degree of machining austenitic stainless steel and prolonging its cutting life, which can greatly improve the comprehensive performance of the tool. © 2022, Chongqing Wujiu Periodicals Press. All rights reserved.
引用
收藏
页码：292 / 298and307
相关论文
共 15 条
  • [1] LIANG Jian-xiong, LIU Zhen-bao, YANG Zhi-yong, Development and Application of High Strength Stainless Steel, Aerospace Materials & Technology, 43, 3, pp. 1-11, (2013)
  • [2] LIU Zhen-bao, LIANG Jian-xiong, SU Jie, Et al., Research and Application Progress in Ultra-High Strength Stainless Steel, Acta Metallurgica Sinica, 56, 4, pp. 549-557, (2020)
  • [3] WANG Yuan-qing, YUAN Huan-xin, SHI Yong-jiu, Et al., A Review of Current Applications and Research of Stainless Steel Structure, Steel Construction, 25, 2, pp. 1-12, (2010)
  • [4] WANG Yun-tao, BU Mao-dong, Present Research and Progress on Low-Nickel and Nickel-Free Austenitic Stainless Steels, Heat Treatment of Metals, 38, 1, pp. 15-20, (2013)
  • [5] LI Xue-kun, CHEN Ze-biao, CHEN Ming, Et al., Research on Wear Mechanism of Coated HSS Drills during Machining Stainless Steel, China Mechanical Engineering, 17, 4, pp. 354-357, (2006)
  • [6] ZHENG Wen-hu, Machining Technology of Hard Cutting Materials, (2008)
  • [7] NAYAK S K, PATRO J K, DEWANGAN S, Et al., Multi-Objective Optimization of Machining Parameters during Dry Turning of AISI 304 Austenitic Stainless Steel Using Grey Relational Analysis, Procedia Materials Science, 6, pp. 701-708, (2014)
  • [8] DINIZ A E, MACHADO A R, CORREA J G., Tool Wear Mechanisms in the Machining of Steels and Stainless Steels, The International Journal of Advanced Manufacturing Technology, 87, 9-12, pp. 3157-3168, (2016)
  • [9] CORREA J G, SCHROETER R B, MACHADO A R., Tool Life and Wear Mechanism Analysis of Carbide Tools Used in the Machining of Martensitic and Supermarten-sitic Stainless Steels, Tribology International, 105, pp. 102-117, (2017)
  • [10] DOLINSEK S., Work-Hardening in the Drilling of Austenitic Stainless Steels, Journal of Materials Processing Tech-nology, 133, 1-2, pp. 63-70, (2003)
12