Calibration of Simulation Parameters of Mung Bean Seeds Using Discrete Element Method and Verification of Seed-metering Test

被引：0

作者：

Zhang S. ^{[1
]}

Zhang R. ^{[1
]}

Chen T. ^{[1
]}

Fu J. ^{[1
,2
]}

Yuan H. ^{[1
,2
]}

机构：

[1] College of Biological and Agricultural Engineering, Jilin University, Changchun

[2] Key Laboratory of Bionics Engineering, Ministry of Education, Jilin University, Changchun

来源：

Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery | 2022年 / 53卷 / 03期

关键词：

Calibration; Discrete element; Mung bean; Seeding test; Simulation parameter;

D O I：

10.6041/j.issn.1000-1298.2022.03.007

中图分类号：

学科分类号：

摘要：

In order to improve the accuracy of the simulation parameters used in the discrete element simulation test of mung bean precision metering process, and further optimize the metering structure, based on the intrinsic parameters of mung bean seeds, the Hertz Mindlin with bonding model was used to establish the seed simulation model, the simulation parameters between the mung bean seeds and the contact material (plexiglass plate, Somos8000 resin) were calibrated by the free fall collision method, inclined sliding method, and inclined rolling method, respectively. The statistical results showed the collision recovery coefficient, static friction coefficient and rolling friction coefficient between mung bean and plexiglass were 0.445, 0.458 and 0.036, respectively; the collision recovery coefficient, static friction coefficient, and rolling friction coefficient between mung bean and Somos8000 resin were 0.434, 0.556 and 0.049, respectively. Steep climbing test, three-factor and five-level horizontal rotation combinations were designed and tested respectively, involving factors of contact parameters between seeds, and the indices of the relative error between the measured accumulation angle and the simulated accumulation angle. Then, the minimum relative error was taken as the optimization objective, and the test data were optimized and analyzed, the collision recovery coefficient, static friction coefficient, and rolling friction coefficient between mung bean seeds were 0.3, 0.23 and 0.03, respectively. Seeding verification tests were carried out on the calibration results, the statistical results showed that the maximum relative error between the leakage rate of the simulation test and the missing rate of the bench test was 4.71%, the maximum relative error between the reabsorption rate and the multiple rate was 4.94%, and the maximum relative error between the single particle rate and the qualified rate was 0.98%, which proved that the calibration results were reliable. It can provide important reference significance for the design and simulation optimization of mung bean precision metering device. © 2022, Chinese Society of Agricultural Machinery. All right reserved.

引用

页码：71 / 79

页数：8

共 26 条

[1] LI Yuhuan, WEI Ya'nan, YANG Li, Et al., Design and experiment of mung bean precision seed-metering device with disturbance for promoting seed flling, Transactions of the Chinese Society for Agricultural Machinery, 51, pp. 50-60, (2020)
[2] JIA Honglei, ZHANG Shengwei, CHEN Tianyou, Et al., Design and experiment of self-suction mung bean precision seed metering device for hilly slope, Transactions of the Chinese Society for Agricultural Machinery, 51, 3, pp. 51-60, (2020)
[3] LI Yuhuan, YANG Li, ZHANG Dongxing, Et al., Design and experiment of pneumatic precision seed-metering device with single seed-metering plate for double-row, Transactions of the Chinese Society for Agricultural Machinery, 50, 7, pp. 61-73, (2019)
[4] DING Li, YANG Li, WU Dehao, Et al., Simulation and experiment of corn air suction seed metering device based on DEM-CFD coupling method, Transactions of the Chinese Society for Agricultural Machinery, 49, 11, pp. 55-64, (2018)
[5] HAN Dandan, ZHANG Dongxing, YANG Li, Et al., Optimization and experiment of inside-filling air-blowing seed metering device based on EDEM-CFD, Transactions of the Chinese Society for Agricultural Machinery, 48, 11, pp. 48-56, (2017)
[6] LEI X, HU H, WU W, Et al., Seed motion characteristics and seeding performance of a centralised seed metering system for rapeseed investigated by DEM simulation and bench testing, Biosystems Engineering, 203, 22, pp. 22-33, (2021)
[7] WANG Jinwu, TANG Han, WANG Qi, Et al., Numerical simulation and experiment on seeding performance of pickup finger precision seed-metering device based on EDEM, Transactions of the CSAE, 31, 21, pp. 51-58, (2015)
[8] WU Z, LI M, LEI X, Et al., Simulation and parameter optimisation of a centrifugal rice seeding spreader for a UAV, Biosystems Engineering, 192, pp. 275-293, (2020)
[9] SHI Song, ZHANG Dongxing, YANG Li, Et al., Simulation and verification of seed-filling performance of pneumatic-combined holes maize precision seed-metering device based on EDEM, Transactions of the CSAE, 31, 3, pp. 62-69, (2015)
[10] LIAO Qingxi, ZHANG Pengling, LIAO Yitao, Et al., Numerical simulation on seeding performance of centrifugal rape-seed metering device based on EDEM, Transactions of the Chinese Society for Agricultural Machinery, 45, 2, pp. 109-114, (2014)

← 1 2 3 →