NATURAL VIBRATION ANALYSIS OF TWO-DIMENSIONAL FLEXIBLE WING BASED ON NON-UNIFORM BEAM MODEL

被引：0
|
作者：
Huang K. [1 ]
Zhang J. [1 ]
Wang Q. [1 ]
机构：
[1] School of Aeronautic Science and Engineering, Beihang University, Beijing
来源：
Lixue Xuebao/Chinese Journal of Theoretical and Applied Mechanics | 2023年 / 55卷 / 02期
关键词：
camber variation; FishBAC; natural vibration; nonuniform beam; power series solution;
D O I：
10.6052/0459-1879-22-551
中图分类号：
学科分类号：
摘要：
In order to improve the flight performance of the aircraft, morphing technologies are used to change aerodynamic characteristics through smooth and continuous structural deformation. Since this new concept requires changing the structural shape to obtain the best performance, its inherent dynamic characteristics will be affected and even change its aeroelastic performance. In this paper, an equivalent modelling method of the two-dimensional flexible wing with camber morphing is developed. The dynamic model of the flexible wing is established based on the hypothesis of a non-uniform beam model. The analytical solution and natural frequencies are obtained by the method of Frobenius and verified by comparison with the finite element method solution. The errors of the first four natural frequencies are within 1% and the corresponding modes are consistent. The flexible wing is prepared by 3D printing engineering plastic (ABS) and silicone rubber skin. The Young's modulus of the 3D printing material and silicone rubber are respectively measured by dynamic measurement method and tensile test. The vibration response test platform is built to carry out vibration test of the flexible wing. It is found that the fundamental frequency obtained by vibration test is consistent with the theoretical model results, and the error is less than 3% compared with the finite element method. The equivalent modelling method of a two-dimensional flexible wing is established through theoretical analysis and experimental verification. The research results will provide theoretical support for applying the flexible trailing edge structures. © 2023 Chinese Journal of Theoretical and Applied Mechanics Press. All rights reserved.
引用
收藏
页码：487 / 496
页数：9
相关论文
共 34 条
  • [1] Barbarino S, Bilgen O, Ajaj RM, Et al., A review of morphing aircraft, Journal of Intelligent Material Systems and Structures, 22, 9, pp. 823-877, (2011)
  • [2] Cistone J., Next century aerospace traffic management: the sky is no longer the limit, Journal of Aircraft, 41, 1, pp. 36-42, (2004)
  • [3] Ajaj RM, Parancheerivilakkathil MS, Amoozgar M, Et al., Recent developments in the aeroelasticity of morphing aircraft, Progress in Aerospace Sciences, 120, (2020)
  • [4] Sun Yang, Chang Min, Bai Junqiang, Review of morphing wing aircraft, Unmanned Systems Technology, 4, 3, pp. 65-77, (2021)
  • [5] Nie Rui, Research on key technologies of morphing wing structures, (2018)
  • [6] Wang C., Design and optimisation of morphing aircraft, (2018)
  • [7] Wang Binwen, Yang Yu, Qian Zhanshen, Et al., Technical development of variable camber wing: review, Acta Aeronautica et Astronautica Sinica, 43, 1, pp. 144-163, (2022)
  • [8] Woods BKS, Bilgen O, Friswell MI., Wind tunnel testing of the fish bone active camber morphing concept, Journal of Intelligent Material Systems and Structures, 25, 7, pp. 772-785, (2014)
  • [9] Rivero AE, Fournier S, Manolesos M, Et al., Experimental aerodynamic comparison of active camber morphing and trailing edge flaps, AIAA Journal, 59, 7, pp. 2627-2640, (2021)
  • [10] Wang C, Khodaparast HH, Friswell MI., Conceptual study of a morphing winglet based on unsymmetrical stiffness, Aerospace Science and Technology, 58, pp. 546-558, (2016)
1234