Experiments on the Resistance Mechanism of Low-Hardness Polyurea/Steel Composite Structures Penetrated by High-Velocity Fragments

被引：0
|
作者：
Mao L. [1 ]
Wan C. [2 ]
Chen C. [2 ,3 ]
Cheng Y. [2 ,3 ]
机构：
[1] Naval Research Institute, Beijing
[2] School of Naval Architecture and Ocean Engineering, Huazhong University of Science and Technology, Hubei, Wuhan
[3] Hubei Key Laboratory of Naval Architecture & Ocean Hydrodynamics, Hubei, Wuhan
来源：
Beijing Ligong Daxue Xuebao/Transaction of Beijing Institute of Technology | 2022年 / 42卷 / 10期
关键词：
composite structure; energy dissipation mechanism; high-velocity penetration; perforation mechanics; polyurea;
D O I：
10.15918/j.tbit1001-0645.2021.219
中图分类号：
学科分类号：
摘要：
To explore the resistance mechanism of low-hardness polyurea/steel composite structures (PSCSs) penetrated by high-velocity fragments, ballistic tests were carried out. Failure modes and ballistic resistances of PSCSs were analyzed, and were compared with those of monolithic steel plates. On the basis of stress waves, ballistic resistance mechanisms of PSCSs were probed. Results show that the front polyurea layers mainly exhibit shearing plugging under high-velocity penetration by fragments, while the failure modes of rear steel layers change from shearing plugging to petalling. Under the same total areal density, the whole ballistic resistance of PSCSs is lower than that of monolithic steel plates, but the ballistic resistance efficiency of rear steel layers is promoted due to the influence of front polyurea layers. The whole ballistic resistance of PSCSs first decreases and then increases, instead of constantly decreasing, as the areal density ratio of front polyurea layer to rear steel layer increases. For a PSCS, the rear steel layer is its main energy absorption component. © 2022 Beijing Institute of Technology. All rights reserved.
引用
收藏
页码：1017 / 1025
页数：8
相关论文
共 18 条
  • [1] GAN Yundan, SONG Li, YANG Liming, Numerical simulation for anti-blast performances of steel plate coated with elastomer, Acta Armamentarii, 30, pp. 15-18, (2009)
  • [2] WANG Ximeng, LIU Jun, CHEN Changhai, Et al., Simulation on dynamic response characteristics of steel/polyurea composite structures under close-range air blast loading[J], Chinese Journal of Ship Research, 16, 2, pp. 116-124, (2021)
  • [3] GOSWAMI A, ADHIKARY S D., Retrofitting materials for enhanced blast performance of structures: recent advancement and challenges ahead[J], Construction and Building Materials, 204, pp. 224-243, (2019)
  • [4] ZHANG Xiaoyu, Numerical simulation of polyurea-retrofitted large LNG storage tank subjected to blast loading, (2018)
  • [5] AMINI M R, ISAACS J, NEMAT-NASSER S., Experimental investigation of response of monolithic and bilayer plates to impulsive loads[J], International Journal of Impact Engineering, 37, (2010)
  • [6] ACKLAND K, ANDERSON C, NGO T D., Deformation of polyurea-coated steel plates under localised blast loading[J], International Journal of Impact Engineering, 51, pp. 13-22, (2013)
  • [7] HOU H L, CHEN C H, CHENG Y S, Et al., Effect of structural configuration on air blast resistance of polyurea-coated composite steel plates: experimental studies[J], Materials & Design, 182, (2019)
  • [8] LI Y Q, CHEN C H, HOU H L, Et al., The influence of spraying strategy on the dynamic response of polyurea-coated metal plates to localized air blast loading: experimental investigations [J], Polymers, 11, (2019)
  • [9] ZHAO Pengduo, ZHANG Peng, ZHANG Lei, Et al., Experimental investigation on the performance of polyurea-coated structure under blast loads[J], Transactions of Beijing Institute of Technology, 38, 2, pp. 118-123, (2018)
  • [10] MOHOTTI D, NGO T, MENDIS P, Et al., Polyurea coated composite aluminium plates subjected to high velocity projectile impact[J], Materials & Design, 52, (2013)
12