Experimental Study on Mechanical Properties of Ductile-Iron Joint Panels for Segmental Joints in Deep-Buried Drainage Shield Tunnels

被引：0
|
作者：
Yan Z. [1 ,2 ,3 ]
Zhou L. [3 ]
Zhu H. [1 ,2 ,3 ]
Shen Y. [1 ,2 ]
机构：
[1] State Key Laboratory of Disaster Reduction in Civil Engineering, Tongji University, Shanghai
[2] Key Laboratory of Geotechnical and Underground Engineering of the Ministry of Education, Tongji University, Shanghai
[3] College of Civil Engineering, Tongji University, Shanghai
来源：
Tongji Daxue Xuebao/Journal of Tongji University | 2019年 / 47卷 / 03期
关键词：
Deep-buried drainage shield tunnel; Ductile-iron joint panel; Experiment; High-stiffness segmental joint;
D O I：
10.11908/j.issn.0253-374x.2019.03.005
中图分类号：
学科分类号：
摘要：
To study the applicability of DIJPs (ductile-iron joint panels) suitable for deep-buried drainage shield tunnels, positive bending moment tests for HSSJs with two different types of DIJPs were carried out, and the mechanical properties of DIJPs and the failure modes of HSSJs were analyzed. The experimental results show that: the failure characteristic of HSSJs subjected to positive bending moment, which is similar to the failure characteristic of the compression-bending section with large eccentricity, is that the bolts or the DIJPs yield firstly, and then the segmental joint fails with the concrete in the compressive zone broken. If the flexural rigidity of the DIJPs is sufficient, there is no deformation in the DIJPs, the bearing capacity of the segmental joint is higher, and the anchor bars reach their full potential; if the flexural rigidity of the DIJPs is insufficient, 5 mm bending deflection appears in the DIJPs, the bearing capacity of the segmental joint is lower, and the anchor function of anchor bars is not fully exploited. © 2019, Editorial Department of Journal of Tongji University. All right reserved.
引用
收藏
页码：331 / 338
页数：7
相关论文
共 20 条
  • [1] Arnau O., Molins C., Experimental and analytical study of the structural response of segmental tunnel linings based on an in situ loading test. Part 2: Numerical simulation, Tunnelling and Underground Space Technology, 26, 6, (2011)
  • [2] Ye F., Gou C.F., Sun H.D., Et al., Model test study on effective ratio of segment transverse bending rigidity of shield tunnel, Tunnelling and Underground Space Technology, 41, (2014)
  • [3] Zhang Z., Zhu Y., Zhu Y., Et al., Study on the longitudinal mechanical behavior of large shield lining structure with a special-shaped cross-section, Journal of Tongji University (Natural Science), 45, 5, (2017)
  • [4] Koyoma Y., Nishimura T., The design of lining segment of shield tunnel using a beam-spring model, Railway Technical Research Institute, Quarterly Reports, 39, 1, (1998)
  • [5] Ding W.Q., Yue Z.Q., Tham L.G., Et al., Analysis of shield tunnel, International Journal for Numerical and Analytical Methods in Geomechanics, 28, 1, (2004)
  • [6] Zhong X.C., Zhu W., Huang Z.G., Et al., Effect of joint structure on joint stiffness for shield tunnel lining, Tunnelling and Underground Space Technology, 21, 3, (2006)
  • [7] Teachavorasinskun S., Chub-Uppakarn T., Influence of segmental joints on tunnel lining, Tunnelling and Underground Space Technology, 25, 4, (2010)
  • [8] Yan Z., Peng Y., Ding W., Et al., Load tests on segment joints of single lining structure of shield tunnel in Qingcaosha Water Conveyance Project, Chinese Journal of Geotechnical Engineering, 33, 9, (2011)
  • [9] Huang H., Shen X., Wang F., Et al., Vulnerability analysis and assessment of segment joints in shield tunnel, Journal of Tongji University (Natural Science), 44, 2, (2015)
  • [10] Peng Y., Ding W., Shen B., Et al., A study on flexural rigidity of single lining segment joint of Shanghai Qingcaosha Water Tunnel, Chinese Journal of Underground Space and Engineering, 9, 5, (2013)
12